Bend Angle & Spring Angle - Revision history

Fabcam1 at 14:07, 6 October 2015

2015-10-06T14:07:49Z

Fabcam1 at 14:07, 6 October 2015

2015-10-06T14:07:18Z

Fabcam1 at 20:04, 26 June 2014

2014-06-26T20:04:40Z

Fabcam1 at 19:58, 26 June 2014

2014-06-26T19:58:02Z

Fabcam1 at 19:55, 26 June 2014

2014-06-26T19:55:54Z

Fabcam1 at 19:54, 26 June 2014

2014-06-26T19:54:16Z

Fabcam1 at 21:26, 9 June 2014

2014-06-09T21:26:31Z

Fabcam1: Created page with "The Bend Angle or "Angle" displayed in the results chart is the angle required as a finished angle. The spring back is not calculated into this angle. With SE you can change t..."

2014-06-05T14:17:49Z

Created page with "The Bend Angle or "Angle" displayed in the results chart is the angle required as a finished angle. The spring back is not calculated into this angle. With SE you can change t..."

New page

The Bend Angle or "Angle" displayed in the results chart is the angle required as a finished angle. The spring back is not calculated into this angle. With SE you can change the decimal places by using the "Tolorance" tab in the "Options" window.

BendSpringAngle2.png

For those that have SE and the Spring Charts filled out you can select the "Display Spring Angle" check box and find the Spring Angles also in the chart.

BendSpringAngle1.png

← Older revision		Revision as of 14:07, 6 October 2015
Line 1:		Line 1:
−	The Bend Angle or '''"Angle"''' displayed in the results chart is the angle required as a finished angle. The spring back is not calculated into this angle. With SE you can change the decimal places by using the '''"Tolerance"''' tab in the "Options" window.	+	The Bend Angle or '''"Angle"''' displayed in the results chart is the angle required as a finished angle. The spring back is not calculated into this angle. With SE you can change the decimal places by using the '''"Tolerance"''' tab in the '''"Options"''' window.

	[[File:BendSpringAngle2.jpg]]		[[File:BendSpringAngle2.jpg]]

@@ Line 1: / Line 1: @@
-The Bend Angle or "Angle" displayed in the results chart is the angle required as a finished angle. The spring back is not calculated into this angle. With SE you can change the decimal places by using the "Tolorance" tab in the "Options" window.
+The Bend Angle or '''"Angle"''' displayed in the results chart is the angle required as a finished angle. The spring back is not calculated into this angle. With SE you can change the decimal places by using the '''"Tolerance"''' tab in the "Options" window.
 [[File:BendSpringAngle2.jpg]]
-For those that have SE and the Spring Charts filled out you can select the "Display Spring Angle" check box and find the Spring Angles also in the chart in two ways. You can click the the '''"Tools"''' tab and then click '''"Options"'''. Next click '''"Design Setting"''' and check the display spring angle box. Or, you can click the '''"LRA Settings"''' button and check the display spring angles box.
+For those that have SE and the Spring Charts filled out you can check the '''"Display Spring Angle"''' check box and find the Spring Angles also in the chart in two ways. You can click the the '''"Tools"''' tab and then click '''"Options"'''. Next, click '''"Design Settings"''' and check the display spring angle box. Or, you can click the '''"LRA Settings"''' button and check the display spring angles box as well.
 [[File:springangle1.jpg|500px]][[File:springangle2.jpg]][[File:BendSpringAngle1.jpg|500px]]

@@ Line 3: / Line 3: @@
 [[File:BendSpringAngle2.jpg]]
-For those that have SE and the Spring Charts filled out you can select the "Display Spring Angle" check box and find the Spring Angles also in the chart in two ways. You can
+For those that have SE and the Spring Charts filled out you can select the "Display Spring Angle" check box and find the Spring Angles also in the chart in two ways. You can click the the '''"Tools"''' tab and then click '''"Options"'''. Next click '''"Design Setting"''' and check the display spring angle box. Or, you can click the '''"LRA Settings"''' button and check the display spring angles box.
 [[File:springangle1.jpg|500px]][[File:springangle2.jpg]][[File:BendSpringAngle1.jpg|500px]]

← Older revision		Revision as of 19:58, 26 June 2014
Line 5:		Line 5:
	For those that have SE and the Spring Charts filled out you can select the "Display Spring Angle" check box and find the Spring Angles also in the chart in two ways. You can		For those that have SE and the Spring Charts filled out you can select the "Display Spring Angle" check box and find the Spring Angles also in the chart in two ways. You can

−	[[File:springangle1.jpg]][[File:springangle2.jpg]][[File:BendSpringAngle1.jpg]]	+	[[File:springangle1.jpg\|500px]][[File:springangle2.jpg]][[File:BendSpringAngle1.jpg\|500px]]

← Older revision		Revision as of 19:55, 26 June 2014
Line 5:		Line 5:
	For those that have SE and the Spring Charts filled out you can select the "Display Spring Angle" check box and find the Spring Angles also in the chart in two ways. You can		For those that have SE and the Spring Charts filled out you can select the "Display Spring Angle" check box and find the Spring Angles also in the chart in two ways. You can

−	[[File:BendSpringAngle1.jpg]]	+	[[File:springangle1.jpg]][[File:springangle2.jpg]][[File:BendSpringAngle1.jpg]]

@@ Line 1: / Line 1: @@
 The Bend Angle or "Angle" displayed in the results chart is the angle required as a finished angle. The spring back is not calculated into this angle. With SE you can change the decimal places by using the "Tolorance" tab in the "Options" window.
-BendSpringAngle2.png
+[[File:BendSpringAngle2.jpg]]
 For those that have SE and the Spring Charts filled out you can select the "Display Spring Angle" check box and find the Spring Angles also in the chart.
-BendSpringAngle1.png
+[[File:BendSpringAngle1.jpg]]