Creating an Angle Dimension - Revision history

Fabcam1 at 19:16, 30 September 2015

2015-09-30T19:16:32Z

Fabcam1 at 20:04, 25 June 2014

2014-06-25T20:04:12Z

Fabcam1 at 20:02, 25 June 2014

2014-06-25T20:02:05Z

Fabcam1 at 20:58, 9 June 2014

2014-06-09T20:58:10Z

Fabcam1 at 19:33, 5 June 2014

2014-06-05T19:33:35Z

Fabcam1: Created page with "Creating an angle dimension requires a little more finesse than defining a simple horizontal or vertical dimension. NOTE: In some cases you may need to create an additional P..."

2014-06-04T22:00:15Z

Created page with "Creating an angle dimension requires a little more finesse than defining a simple horizontal or vertical dimension. NOTE: In some cases you may need to create an additional P..."

New page

Creating an angle dimension requires a little more finesse than defining a simple horizontal or vertical dimension.

NOTE: In some cases you may need to create an additional PickPoint to have the number of points required.

To create an angle dimension you need to pick both ends of the line that represents the angle. The order of the selections is outside-in for each line.

Select the "Angle Dim" command button.

Select the "PickPoints" in the order shown. Line one, outside-in. Line two, outside-in.

AngleDim1.png

Select a screen location with your cursor. NOTE: not a PickPoint for this selection.

AngleDim2.png

This next picture will be the end result:

AngleDim3.png

← Older revision		Revision as of 19:16, 30 September 2015
Line 9:		Line 9:
	Select the '''"Lines"''' in the order shown. Line one, outside-in. Line two, outside-in.		Select the '''"Lines"''' in the order shown. Line one, outside-in. Line two, outside-in.

−	[[File:AngleDim1.~~jpg~~]]	+	[[File:AngleDim1.png]]

← Older revision		Revision as of 20:04, 25 June 2014
Line 10:		Line 10:

	[[File:AngleDim1.jpg]]		[[File:AngleDim1.jpg]]
−
−
−	~~'''Select a screen location with your cursor.''' NOTE: not a PickPoint for this selection.~~
−
−	~~[[FIle:AngleDim2.jpg]]~~
−
−
−	~~This next picture will be the end result:~~
−
−	~~[[File:AngleDim3.jpg]]~~

@@ Line 3: / Line 3: @@
 NOTE: In some cases you may need to create an additional PickPoint to have the number of points required.
-To create an angle dimension you need to pick both ends of the line that represents the angle. The order of the selections is outside-in for each line.
+To create an angle dimension you need to pick the two lines that represent the angle. The order of the selections is outside-in for each line.
 Select the '''"Angle Dim"''' command button.
-Select the '''"PickPoints"''' in the order shown. Line one, outside-in. Line two, outside-in.
+Select the '''"Lines"''' in the order shown. Line one, outside-in. Line two, outside-in.
 [[File:AngleDim1.jpg]]

@@ Line 9: / Line 9: @@
 Select the '''"PickPoints"''' in the order shown. Line one, outside-in. Line two, outside-in.
-AngleDim1.png
+[[File:AngleDim1.jpg]]
 '''Select a screen location with your cursor.''' NOTE: not a PickPoint for this selection.
-AngleDim2.png
+[[FIle:AngleDim2.jpg]]
 This next picture will be the end result:
-AngleDim3.png
+[[File:AngleDim3.jpg]]