Cutting the End of a Straight Tube - Revision history

Fabcam1 at 21:13, 5 October 2015

2015-10-05T21:13:22Z

Fabcam1 at 21:19, 9 June 2014

2014-06-09T21:19:58Z

Fabcam1 at 21:19, 9 June 2014

2014-06-09T21:19:42Z

Fabcam1 at 20:02, 5 June 2014

2014-06-05T20:02:25Z

Fabcam1: Created page with "A straight part is a part defined without a bend. Following are the steps to setting up the cutting for a straight part. Step 1) Select the "Cutting" tab. Step 2) Select th..."

2014-06-05T14:13:00Z

Created page with "A straight part is a part defined without a bend. Following are the steps to setting up the cutting for a straight part. Step 1) Select the "Cutting" tab. Step 2) Select th..."

New page

A straight part is a part defined without a bend.

Following are the steps to setting up the cutting for a straight part.

Step 1) Select the "Cutting" tab.

Step 2) Select the "New Cut" command button.

Step 3) Select the tube you are going to cut. Note: The straight parts have 2 red dots on each part. You need select the red dot closest to the end you are going to cut. You will find our part turn green in color.

CutEndStraight1.png

Step 4) Select the dot(s) representing the tube section(s) that our part is going to be cut to. You will find the intersecting tubes will turn red.

CutEndStraight2.png

Step 5) Select the "Cut Complete" command button.

CutEndStraight3.png

Notice the intersection now has a black and a blue cut marks showing the inside and outside of the material where each meets the intersection part(s).

Step 6) Select the "Print" command button.

CutEndStraight4.png

The cutting templates can be called up at a later time by selecting them from the list shown.

NOTE: If you desire a cut wrapper for both ends of a single straight tube, print out the wrappers AFTER both cuts have been defined. This will allow for proper rotational calibration (blue lines) and proper distance between the wrappers calibration (red calibration lines).

@@ Line 3: / Line 3: @@
 Following are the steps to setting up the cutting for a straight part.
-Step 1) Select the '''"Cutting"''' tab.
+'''Step 1:''' Select the '''"Cutting"''' tab.
-Step 2) Select the '''"New Cut"''' command button.
+'''Step 2:''' Select the '''"New Cut"''' command button.
-Step 3) '''Select the tube you are going to cut. Note: The straight parts have 2 red dots on each part.''' You need select the red dot closest to the end you are going to cut. You will find our part turn green in color.
+'''Step 3:''' Select the tube you are going to cut. Note: The straight parts have 2 red dots on each part. You need select the red dot closest to the end you are going to cut. You will find our part turn green in color.
 [[File:CutEndStraight1.jpg]]
-Step 4) '''Select the dot(s) representing the tube section(s) that our part is going to be cut to.''' You will find the intersecting tubes will turn red.
+'''Step 4:''' Select the dot(s) representing the tube section(s) that our part is going to be cut to. You will find the intersecting tubes will turn red.
 [[File:CutEndStraight2.jpg]]
-Step 5) Select the '''"Cut Complete"''' command button.
+'''Step 5:''' Select the '''"Cut Complete"''' command button.
 [[File:CutEndStraight3.jpg]]
@@ Line 24: / Line 24: @@
 Notice the intersection now has a black and a blue cut marks showing the inside and outside of the material where each meets the intersection part(s).
-Step 6) Select the''' "Print"''' command button.
+'''Step 6:''' Select the '''"Print"''' command button.
 [[File:CutEndStraight4.jpg]]

← Older revision		Revision as of 21:19, 9 June 2014
Line 26:		Line 26:
	Step 6) Select the''' "Print"''' command button.		Step 6) Select the''' "Print"''' command button.

−	[[~~[FIle~~:CutEndStraight4.jpg]]	+	[[File:CutEndStraight4.jpg]]

@@ Line 9: / Line 9: @@
 Step 3) '''Select the tube you are going to cut. Note: The straight parts have 2 red dots on each part.''' You need select the red dot closest to the end you are going to cut. You will find our part turn green in color.
-CutEndStraight1.png
+[[File:CutEndStraight1.jpg]]
 Step 4) '''Select the dot(s) representing the tube section(s) that our part is going to be cut to.''' You will find the intersecting tubes will turn red.
-CutEndStraight2.png
+[[File:CutEndStraight2.jpg]]
 Step 5) Select the '''"Cut Complete"''' command button.
-CutEndStraight3.png
+[[File:CutEndStraight3.jpg]]
@@ Line 26: / Line 26: @@
 Step 6) Select the''' "Print"''' command button.
-CutEndStraight4.png
+[[[FIle:CutEndStraight4.jpg]]