Dragon A400 Design to Manufacturing Tutorial - Revision history

Fabcam1 at 14:45, 24 August 2017

2017-08-24T14:45:22Z

Fabcam1 at 14:53, 23 August 2017

2017-08-23T14:53:20Z

Fabcam1 at 17:33, 18 August 2017

2017-08-18T17:33:27Z

Fabcam1 at 17:33, 18 August 2017

2017-08-18T17:33:10Z

Fabcam1 at 17:32, 18 August 2017

2017-08-18T17:32:25Z

Fabcam1: Created page with "After installing and getting your initial introduction to the Dragon software and machine processes, there are a few things you should come to know about your setup that are n..."

2017-08-18T17:00:28Z

Created page with "After installing and getting your initial introduction to the Dragon software and machine processes, there are a few things you should come to know about your setup that are n..."

New page

After installing and getting your initial introduction to the Dragon software and machine processes, there are a few things you should come to know about your setup that are not widely known. The machine will shave tons of fabricating time off of your previous methods used in the shop, but we want you well equipped to handle yourself around the software and navigating normal machine actions.

For this reason, we've created this in depth tutorial...

If you'd like to know what each specific area contains, please jump to the corresponding number in this tutorial's table of contents.

[[File:A400_Tutorial1.png]]

← Older revision		Revision as of 14:45, 24 August 2017
Line 13:		Line 13:

	'''A part created in Bent Part can be sent to Edit Flat to edit simple cutting, marking or engraving actions, kerf offset, lead ins and outs, bending order, etc, or it can be sent to Nest Part to be simply nested on a stock length of tubing, adjust action paths, and ultimately to transfer the project to the machine for manufacturing.'''		'''A part created in Bent Part can be sent to Edit Flat to edit simple cutting, marking or engraving actions, kerf offset, lead ins and outs, bending order, etc, or it can be sent to Nest Part to be simply nested on a stock length of tubing, adjust action paths, and ultimately to transfer the project to the machine for manufacturing.'''
		+
		+	[[File:A400_Tutorial2.png]]

@@ Line 8: / Line 8: @@
 =1. Bent Part=
 '''The Bent Part interface is used to create a bent part, applied with your self-created die (pulled from the Die Library), and will allow you to create copes/notches, miters and holes on the part before it can be nested out and sent to the machine for cutting and marking.'''
 '''A part created in Bent Part can be sent to Edit Flat to edit simple cutting, marking or engraving actions, kerf offset, lead ins and outs, bending order, etc, or it can be sent to Nest Part to be simply nested on a stock length of tubing, adjust action paths, and ultimately to transfer the project to the machine for manufacturing.'''

@@ Line 7: / Line 7: @@
 [[File:A400_Tutorial1.png]]
-<h1>1. Bent Part<h1/>
+=1. Bent Part=
 '''The Bent Part interface is used to create a bent part, applied with your self-created die (pulled from the Die Library), and will allow you to create copes/notches, miters and holes on the part before it can be nested out and sent to the machine for cutting and marking.'''
 '''A part created in Bent Part can be sent to Edit Flat to edit simple cutting, marking or engraving actions, kerf offset, lead ins and outs, bending order, etc, or it can be sent to Nest Part to be simply nested on a stock length of tubing, adjust action paths, and ultimately to transfer the project to the machine for manufacturing.'''

@@ Line 7: / Line 7: @@
 [[File:A400_Tutorial1.png]]
-=1. Bent Part=
+<h1>1. Bent Part<h1/>
 '''The Bent Part interface is used to create a bent part, applied with your self-created die (pulled from the Die Library), and will allow you to create copes/notches, miters and holes on the part before it can be nested out and sent to the machine for cutting and marking.'''
 '''A part created in Bent Part can be sent to Edit Flat to edit simple cutting, marking or engraving actions, kerf offset, lead ins and outs, bending order, etc, or it can be sent to Nest Part to be simply nested on a stock length of tubing, adjust action paths, and ultimately to transfer the project to the machine for manufacturing.'''

@@ Line 1: / Line 1: @@
-After installing and getting your initial introduction to the Dragon software and machine processes, there are a few things you should come to know about your setup that are not widely known. The machine will shave tons of fabricating time off of your previous methods used in the shop, but we want you well equipped to handle yourself around the software and navigating normal machine actions.
+'''After installing and getting your initial introduction to the Dragon software and machine processes, there are a few things you should come to know about your setup that are not widely known. The machine will shave tons of fabricating time off of your previous methods used in the shop, but we want you well equipped to handle yourself around the software and navigating normal machine actions.'''
-For this reason, we've created this in depth tutorial...
+'''For this reason, we've created this in depth tutorial...'''
-If you'd like to know what each specific area contains, please jump to the corresponding number in this tutorial's table of contents.
+'''If you'd like to know what each specific area contains, please jump to the corresponding number in this tutorial's table of contents.'''
 [[File:A400_Tutorial1.png]]