Dragon Diamond Notch Bridging Tutorial - Revision history

Fabcam1 at 16:35, 4 October 2017

2017-10-04T16:35:12Z

2017-10-04T16:30:00Z

2017-10-04T16:19:30Z

2017-10-04T16:17:01Z

2017-10-04T15:40:43Z

2017-10-04T15:18:23Z

2017-10-03T20:08:21Z

2017-10-03T19:52:47Z

2017-10-03T19:24:48Z

2017-10-03T19:20:52Z

← Older revision		Revision as of 16:35, 4 October 2017
Line 156:		Line 156:


−	'''24.''' Now that the part is finished, you are free to adjust/edit any other geometry in this interface	+	'''24.''' Now that the part is finished, you are free to adjust/edit any other geometry in this interface, or to send this part to the nesting interface using the '''Nest Part''' button located at the top of the screen.


Line 162:		Line 162:


		+	'''25.''' Here, you can designate the stock length of your tubing in the '''Setup''' tab, add your part to the stock length in the '''Parts''' tab, and view the machine order of actions in the '''Shifts''' tab.


		+	[[File:DNB29.png]]

−	[[File:~~DNB29~~.png]]	+
		+	'''26.''' Finally, you can send the job to the machine by selecting the '''Run Project''' button at the top of the screen.
		+
		+
		+	[[File:DNB30.png]]

← Older revision		Revision as of 16:30, 4 October 2017
Line 150:		Line 150:


−	'''23.''' Lastly, select the center of your notch to place the bridging option as shown below.	+	'''23.''' Lastly, leave the notch dimensions as they are and select the center of your notch to place the bridging option as shown below.


Line 156:		Line 156:


−		+	'''24.''' Now that the part is finished, you are free to adjust/edit any other geometry in this interface

@@ Line 140: / Line 140: @@
 [[File:DNB24.png]]
 [[File:DNB25.png]]
-'''23.''' Lastly, select the center of your notch to place the bridging option as shown below.
+'''22.''' Then, select the '''Cutting''' button followed by the '''Diamond Tabs''' button.
@@ Line 154: / Line 150: @@
+'''23.''' Lastly, select the center of your notch to place the bridging option as shown below.

← Older revision		Revision as of 16:17, 4 October 2017
Line 136:		Line 136:


−	'''21.'''	+	'''21.''' With the part sent to the Designer interface (also known as Edit Flat), you will '''Maximize''' the screen and select the '''Actions''' tab to the far right.


	[[File:DNB24.png]]		[[File:DNB24.png]]
		+
		+
		+	'''22.''' Then, select the '''Cutting''' button followed by the '''Diamond Tabs''' button.
		+
		+
		+	[[File:DNB25.png]]
		+
		+
		+	'''23.''' Lastly, select the center of your notch to place the bridging option as shown below.
		+
		+
		+	[[File:DNB26.png]]
		+
		+
		+
		+
		+
		+	[[File:DNB27.png]]
		+
		+
		+
		+
		+
		+	[[File:DNB28.png]]
		+
		+
		+
		+
		+
		+	[[File:DNB29.png]]

@@ Line 128: / Line 128: @@
-'''20.'''
+'''20.''' The Dragon CAM software should open if it isn't already (or if it is, you will have to reveal the screen from your computer's task menu - typically below) and the '''Part Transfer''' window will be open. You will want to ensure that you have the same/similar material selected from the drop down menu here and select the '''Designer''' button from below to send this to the Edit Flat/Designer interface.
 [[File:DNB23.png]]
 [[File:DNB24.png]]

@@ Line 116: / Line 116: @@
-'''18.'''
+'''18.''' After checking the 3D display using the '''Display''' button from above, your part should appear like the image below.
 [[File:DNB21.png]]
 [[File:DNB22.png]]
 [[File:DNB23.png]]
 [[File:DNB24.png]]

@@ Line 96: / Line 96: @@
 [[File:DNB16.png]]
 [[File:DNB17.png]]
-[[File:DNB19.png]]
+'''16.''' Leave all of the specific '''Notch Dimensions''' as they are and click on the '''Create Hole''' button at the top of this section.
 [[File:DNB20.png]]
 [[File:DNB21.png]]

@@ Line 86: / Line 86: @@
-'''13.'''
+'''13.''' Under the '''Hole Type''' section, select the '''Notch''' option. ''NOTE: This is only available as a hole type for square or rectangular tubing.''
 [[File:DNB15.png]]
 [[File:DNB16.png]]
 [[File:DNB17.png]]

@@ Line 63: / Line 63: @@
 '''9.''' A window will appear asking if you'd like to indicate a rotational value for the part itself. Leave this value at '''0''' and click the '''OK''' button. Your part should now appear as a '''line''' in the display screen.
@@ Line 70: / Line 68: @@
-'''11.'''
+'''10.''' To view your straight part as a 3D rendering, click on the '''Display''' button from above.
 [[File:DNB12.png]]
 [[File:DNB13.png]]
 [[File:DNB14.png]]
 [[File:DNB15.png]]

← Older revision		Revision as of 19:20, 3 October 2017
Line 62:		Line 62:


−	'''9.''' A window will appear asking if you'd like to indicate a rotational value for the part itself. Leave this value at '0' and click the '''OK''' button. Your part should ~~not~~ appear as a '''line''' in the display screen.	+	'''9.''' A window will appear asking if you'd like to indicate a rotational value for the part itself. Leave this value at '''0''' and click the '''OK''' button. Your part should now appear as a '''line''' in the display screen.
		+
		+	'''10.''' To view your straight part as a 3D rendering, click on the '''Display''' button from above.


Line 68:		Line 70:


−	'''10.''' ~~Now, to view your straight part as a 3D rendering, click on the '''Display''' button from above.~~	+	'''11.'''