Dragon Machine Library - Revision history

Fabcam1: /* Factory Settings */

2017-11-01T20:02:56Z

‎Factory Settings

Fabcam1 at 22:37, 7 February 2017

2017-02-07T22:37:58Z

Fabcam1 at 22:36, 7 February 2017

2017-02-07T22:36:54Z

Fabcam1 at 22:36, 7 February 2017

2017-02-07T22:36:01Z

Fabcam1: /* Machine Limit Warnings */

2016-12-28T21:44:53Z

‎Machine Limit Warnings

Fabcam1: /* Machine Limit Warnings */

2016-12-28T21:36:39Z

‎Machine Limit Warnings

Fabcam1: /* Mechanical Settings */

2016-12-28T21:08:21Z

‎Mechanical Settings

Fabcam1: /* Shift Marks (Default) */

2016-12-28T18:10:44Z

‎Shift Marks (Default)

Fabcam1: /* Action Settings */

2016-12-28T18:09:32Z

‎Action Settings

Fabcam1: /* Bend Marks (Default) */

2016-12-28T17:21:58Z

‎Bend Marks (Default)

← Older revision		Revision as of 20:02, 1 November 2017
Line 262:		Line 262:
	[[File:Dragon_Factory_Settings.png\|right]]		[[File:Dragon_Factory_Settings.png\|right]]

−	'''"IT IS NOT RECOMMENDED TO ADJUST THESE SETTINGS UNLESS YOU KNOW WHAT YOU'RE DOING"'''	+	'''"IT IS NOT RECOMMENDED TO ADJUST THESE SETTINGS UNLESS YOU KNOW WHAT YOU'RE DOING OR ARE INSTRUCTED TO MAKE CHANGES BY A BEND-TECH REPRESENTATIVE."'''

@@ Line 228: / Line 228: @@
 '''"IT IS NOT RECOMMENDED TO ADJUST THESE SETTINGS UNLESS YOU KNOW WHAT YOU'RE DOING"'''
@@ Line 260: / Line 261: @@
 =Factory Settings=
 [[File:Dragon_Factory_Settings.png|right]]

← Older revision		Revision as of 22:36, 7 February 2017
Line 228:		Line 228:

	'''"IT IS NOT RECOMMENDED TO ADJUST THESE SETTINGS UNLESS YOU KNOW WHAT YOU'RE DOING"'''		'''"IT IS NOT RECOMMENDED TO ADJUST THESE SETTINGS UNLESS YOU KNOW WHAT YOU'RE DOING"'''
		+
		+
		+
		+
		+
		+
		+
		+
		+
		+

@@ Line 223: / Line 223: @@
 *'''Enable A Limits''' '''-Min-''' Enter the minimum value allowed for the A travel here. This value can be less than zero (Home Position) but should not exceed the travel limit of the machine. '''-Max-''' Enter the maximum value allowed for the A travel here. This value should not exceed the travel limit of the machine.
 =Factory Settings=
 [[File:Dragon_Factory_Settings.png|right]]

@@ Line 218: / Line 218: @@
 '''"IT IS NOT RECOMMENDED TO ADJUST THESE SETTINGS UNLESS YOU KNOW WHAT YOU'RE DOING"'''
-*'''Enable X Limits''' Enter the minimum value allotted for the X travel here. This value can be less than zero (Home Position) but should not exceed the travel limit of the machine.
+*'''Enable X Limits''' Enter the minimum value allowed for the X travel here. This value can be less than zero (Home Position) but should not exceed the travel limit of the machine.
-*'''Enable Z Limits''' Enter the minimum value allotted for the Z travel here. This value can be less than zero (Home Position) but should not exceed the travel limit of the machine.
+*'''Enable Z Limits''' '''-Min-''' Enter the minimum value allowed for the Z travel here. This value can be less than zero (Home Position) but should not exceed the travel limit of the machine. '''-Max-''' Enter the maximum value allowed for the Z travel here. This value should not exceed the travel limit of the machine.
-*'''Enable A Limits''' Enter the minimum value allotted for the A travel here. This value can be less than zero (Home Position) but should not exceed the travel limit of the machine.
+*'''Enable A Limits''' '''-Min-''' Enter the minimum value allowed for the A travel here. This value can be less than zero (Home Position) but should not exceed the travel limit of the machine. '''-Max-''' Enter the maximum value allowed for the A travel here. This value should not exceed the travel limit of the machine.
 =Factory Settings=
 [[File:Dragon_Factory_Settings.png|right]]

@@ Line 211: / Line 211: @@
 ==Axis Step Correction==
 *Use the '''Calibrate''' button to adjust the motor tuning of any given axis.
 =Factory Settings=
 [[File:Dragon_Factory_Settings.png|right]]

← Older revision		Revision as of 18:10, 28 December 2016
Line 192:		Line 192:

	==Shift Marks (Default)==		==Shift Marks (Default)==
		+	*'''Mark:''' Select the '''"Mark"''' [[File:Dragon_Mark_Bend_Marks1.png]] option if you would like the shift marks to be marked with a marker by default.
		+
		+	*'''Engrave:''' Select the '''"Engrave"''' [[File:Dragon_Engrave_Bend_Marks1.png]] option if you would like the shift marks to be engraved by default.

	=Mechanical Settings=		=Mechanical Settings=

← Older revision		Revision as of 18:09, 28 December 2016
Line 190:		Line 190:

	*'''Engrave:''' Select the '''"Engrave"''' [[File:Dragon_Engrave_Bend_Marks1.png]] option and an end cut will be engraved instead of cut by default. The shortest a leg can be before this override occurs is defined by the Die Limitations within the Die Library.		*'''Engrave:''' Select the '''"Engrave"''' [[File:Dragon_Engrave_Bend_Marks1.png]] option and an end cut will be engraved instead of cut by default. The shortest a leg can be before this override occurs is defined by the Die Limitations within the Die Library.
		+
		+	==Shift Marks (Default)==

	=Mechanical Settings=		=Mechanical Settings=

← Older revision		Revision as of 17:21, 28 December 2016
Line 165:		Line 165:

	*'''Mark both sides of Bend:''' Check this check box if you'd like the Dragon machine to mark both tangents of each bend by default.		*'''Mark both sides of Bend:''' Check this check box if you'd like the Dragon machine to mark both tangents of each bend by default.
		+
		+	*'''Mark First Bend Only:''' Check this check box if you'd like the Dragon machine to mark only the first bend mark in on each part.

	==Saddles (Default)==		==Saddles (Default)==