Dragon Tips & Hints - Revision history

Fabcam1 at 17:05, 1 December 2017

2017-12-01T17:05:47Z

Fabcam1: /* Engraver Holder Silicone Rings Replacement */

2017-11-29T22:34:54Z

‎Engraver Holder Silicone Rings Replacement

Fabcam1 at 22:24, 29 November 2017

2017-11-29T22:24:11Z

Fabcam1 at 19:39, 29 September 2017

2017-09-29T19:39:20Z

Fabcam1 at 17:40, 26 June 2017

2017-06-26T17:40:23Z

Fabcam1 at 17:38, 26 June 2017

2017-06-26T17:38:24Z

Fabcam1 at 16:58, 20 April 2017

2017-04-20T16:58:59Z

Fabcam1 at 20:10, 24 March 2017

2017-03-24T20:10:29Z

Fabcam1 at 20:09, 24 March 2017

2017-03-24T20:09:45Z

Fabcam1 at 20:07, 24 March 2017

2017-03-24T20:07:50Z

← Older revision	Revision as of 17:05, 1 December 2017
Line 66:	Line 66:


	+	==Chuck Spindle Cleanup==
	+	[[File:Chuck_Spindle_Cleanup1.png]]

	+	When Carbon Brushes go bad, or are no longer usable causing your plasma torch to misfire, or not continue to fire during operations, most likely the torch is arcing out and will be causing significant scarring on your chuck spindle inside the chuck housing. In this case, we suggest immediately replacing your Carbon Brushes (See above), but also cleaning off any of the scarring on the chuck spindle with emery cloth or a wire brush wheel.

−	+	[[File:Chuck_Spindle_Cleanup2.png]][[File:Chuck_Spindle_Cleanup3.png]]

@@ Line 46: / Line 46: @@
 ==Engraver Holder Silicone Rings Replacement==
-Top Ring: https://www.mcmaster.com/#1283n59/=1agx1v5
+*Top Ring: https://www.mcmaster.com/#1283n59/=1agx1v5
-Bottom Ring: https://www.mcmaster.com/#1283n86/=1agx24g
+*Bottom Ring: https://www.mcmaster.com/#1283n86/=1agx24g
 ==Carbon Grounding Brush Replacement==

← Older revision	Revision as of 22:24, 29 November 2017
Line 42:	Line 42:


	+
	+
	+
	+	==Engraver Holder Silicone Rings Replacement==
	+	[[File:Engraver_O_Rings_Replacement1.png]] [[File:Engraver_O_Rings_Replacement2.png]]
	+
	+	Top Ring: https://www.mcmaster.com/#1283n59/=1agx1v5
	+
	+	Bottom Ring: https://www.mcmaster.com/#1283n86/=1agx24g

@@ Line 1: / Line 1: @@
 '''This page will discuss tips and hints that we've found useful for Dragon users who experience various difficulties with their machine and/or components.'''
-==Gecko Drive Adjustment Instructions==
+==Dragon A150 Gecko Drive Adjustment Instructions==
 '''If you are having concerns with the smoothness related to motor functions on the Dragon Machine,  the Gecko driver (which drives the motors) has a few select dials that can be adjusted in order to improve the efficiency of your machine.'''

@@ Line 2: / Line 2: @@
 ==Gecko Drive Adjustment Instructions==
-'''- If you are having concerns with the smoothness related to motor functions on the Dragon Machine,  the Gecko driver (which drives the motors) has a few select dials that can be adjusted in order to improve the efficiency of your machine.'''
+'''If you are having concerns with the smoothness related to motor functions on the Dragon Machine,  the Gecko driver (which drives the motors) has a few select dials that can be adjusted in order to improve the efficiency of your machine.'''
 [[Gecko Drive Adjustment Instructions]]
@@ Line 18: / Line 18: @@
 [[File:Marker_Holder_Tip1.png]]
-- Sometimes the markers placed in the marker holder slip freely and fall out of the holder. Other times they get jammed up into the holder and are impossible to remove. ''We recommend a black or silver Sharpie for this.'' If the silver Sharpie still slips out of its holder, wrap the marker in tape (we use duct tape, but any tape will do) to ensure that it is held securely in the marker holder.
+Sometimes the markers placed in the marker holder slip freely and fall out of the holder. Other times they get jammed up into the holder and are impossible to remove. ''We recommend a black or silver Sharpie for this.'' If the silver Sharpie still slips out of its holder, wrap the marker in tape (we use duct tape, but any tape will do) to ensure that it is held securely in the marker holder.
 '''Or'''
-- Simply flip the head of the marker holder to the other end of the cylinder and the opposing end should accommodate both black and silver Sharpies.
+Simply flip the head of the marker holder to the other end of the cylinder and the opposing end should accommodate both black and silver Sharpies.
 ==Marker Revival==
-- Sometimes the markers will dry out because they are marking close to a cut zone where the tubing is still hot from the plasma. This can dry out your markers in record time. To bring your dried out marker back to life, dip the tip in some rubbing alcohol and it will work as good as new. It is also smart to make sure that your tubing is wiped down before running the stick to make sure that the grease doesn't inhibit the marker's ability to show up well on the surface.
+Sometimes the markers will dry out because they are marking close to a cut zone where the tubing is still hot from the plasma. This can dry out your markers in record time. To bring your dried out marker back to life, dip the tip in some rubbing alcohol and it will work as good as new. It is also smart to make sure that your tubing is wiped down before running the stick to make sure that the grease doesn't inhibit the marker's ability to show up well on the surface.
 ==Engraver Maintenance==
-- To ensure that your engraver tip lasts as long as possible, we suggest that you invest in an airline oiler and install it in your air line as shown here.
+To ensure that your engraver tip lasts as long as possible, we suggest that you invest in an airline oiler and install it in your air line as shown here.
 [[File:Airline_Oiler_4_Engraver1.png]]
@@ Line 35: / Line 35: @@
 [[File:Engraver_Tip_Replacements1.png]]
-- Sometimes, regardless of preventative maintenance measures taken, the engraver tip will be in need of replacement. In this case, this stylus tip can be purchased at the link available here.
+Sometimes, regardless of preventative maintenance measures taken, the engraver tip will be in need of replacement. In this case, this stylus tip can be purchased at the link available here.
 http://www.centurytool.net/CA156963_Chicago_Pneumatic_Assembly_Stylus_Cp7_p/cptca156963.htm
@@ Line 47: / Line 47: @@
 [[File:Carbon_Brushes_Replacements1.png]]
-- If you've put a significant amount of hours on the Dragon Machine, there may come a time when the carbon grounding brushes will need replacing. These can be purchased at the link available here. (Part ID# 65705K39)
+If you've put a significant amount of hours on the Dragon Machine, there may come a time when the carbon grounding brushes will need replacing. These can be purchased at the link available here. (Part ID# 65705K39)
 https://www.mcmaster.com/#65705K39
@@ Line 58: / Line 58: @@
 ==Rail Maintenance==
-- Your Bend-Tech Dragon machine will require maintenance in is lifetime. The following is a small routine maintenance process that should be completed about once per week, or if you notice build up of grime or dirt on either the main rail or on the roller bearings of the chuck trolly. This process should take less than 10 minutes to complete.
+Your Bend-Tech Dragon machine will require maintenance in is lifetime. The following is a small routine maintenance process that should be completed about once per week, or if you notice build up of grime or dirt on either the main rail or on the roller bearings of the chuck trolly. This process should take less than 10 minutes to complete.
 '''Step 1)''' Send the chuck to the middle of the machine. (Either jog the machine to this location or manually move the chuck while the machine is off.)
@@ Line 70: / Line 70: @@
 '''Step 5)''' Wipe down the section of the main rail that was covered by the trolly before the homing sequence.
-- This will provide a clean working environment for the chuck trolly to roll on and will increase the life of the trolly bearings.
+This will provide a clean working environment for the chuck trolly to roll on and will increase the life of the trolly bearings.
 To ensure that your rail/beam remains in pristine condition and operates up to our standards, make sure to follow through with this process as needed.
@@ Line 76: / Line 76: @@
 ==Frayed or Broken Z-Axis Cable==
-- In the event of a fraying or broken z-axis chain/cable, the part must be replaced. This will require a careful and attentive read through of the instructions contained in the link below.
+In the event of a fraying or broken z-axis chain/cable, the part must be replaced. This will require a careful and attentive read through of the instructions contained in the link below.
 [[File:Pdf2.png|link=http://www.bendtechdragon.com/files/z_axis_cable_replacement_walkthrough.pdf]] '''[http://www.bendtechdragon.com/files/z_axis_cable_replacement_walkthrough.pdf Z-Axis Replacement Cable]'''
 ==Anti-Chattering Retro Fit Assembly Manual==
-- In some cases with older model 21 foot machines, some operators have experienced excessive chattering on the X-travel which has led to jagged or wavy cuts. If this unfortunate phenomenon has been the case for you, we suggest that you contact us and we will send out a retrofit kit to resolve this issue. The assembly manual is located below.
+In some cases with older model 21 foot machines, some operators have experienced excessive chattering on the X-travel which has led to jagged or wavy cuts. If this unfortunate phenomenon has been the case for you, we suggest that you contact us and we will send out a retrofit kit to resolve this issue. The assembly manual is located below.
 [[File:Pdf2.png|link=http://www.bendtechdragon.com/files/anti_chatter_retrofit_assembly_manual.pdf]] '''[http://www.bendtechdragon.com/files/anti_chatter_retrofit_assembly_manual.pdf Anti-Chattering Retro Fit Assembly Manual]'''

← Older revision		Revision as of 16:58, 20 April 2017
Line 1:		Line 1:
	'''This page will discuss tips and hints that we've found useful for Dragon users who experience various difficulties with their machine and/or components.'''		'''This page will discuss tips and hints that we've found useful for Dragon users who experience various difficulties with their machine and/or components.'''
		+
		+	==Gecko Drive Adjustment Instructions==
		+	'''- If you are having concerns with the smoothness related to motor functions on the Dragon Machine, the Gecko driver (which drives the motors) has a few select dials that can be adjusted in order to improve the efficiency of your machine.'''
		+
		+	[[Gecko Drive Adjustment Instructions]]

	==Plasma Gas Selection==		==Plasma Gas Selection==

← Older revision		Revision as of 20:10, 24 March 2017
Line 78:		Line 78:
	- In some cases with older model 21 foot machines, some operators have experienced excessive chattering on the X-travel which has led to jagged or wavy cuts. If this unfortunate phenomenon has been the case for you, we suggest that you contact us and we will send out a retrofit kit to resolve this issue. The assembly manual is located below.		- In some cases with older model 21 foot machines, some operators have experienced excessive chattering on the X-travel which has led to jagged or wavy cuts. If this unfortunate phenomenon has been the case for you, we suggest that you contact us and we will send out a retrofit kit to resolve this issue. The assembly manual is located below.

−	[[File:Pdf2.png\|link=http://www.bendtechdragon.com/files/anti_chatter_retrofit_assembly_manual.pdf]] '''[http://www.bendtechdragon.com/files/anti_chatter_retrofit_assembly_manual.pdf]'''	+	[[File:Pdf2.png\|link=http://www.bendtechdragon.com/files/anti_chatter_retrofit_assembly_manual.pdf]] '''[http://www.bendtechdragon.com/files/anti_chatter_retrofit_assembly_manual.pdf Anti-Chattering Retro Fit Assembly Manual]'''

← Older revision		Revision as of 20:09, 24 March 2017
Line 78:		Line 78:
	- In some cases with older model 21 foot machines, some operators have experienced excessive chattering on the X-travel which has led to jagged or wavy cuts. If this unfortunate phenomenon has been the case for you, we suggest that you contact us and we will send out a retrofit kit to resolve this issue. The assembly manual is located below.		- In some cases with older model 21 foot machines, some operators have experienced excessive chattering on the X-travel which has led to jagged or wavy cuts. If this unfortunate phenomenon has been the case for you, we suggest that you contact us and we will send out a retrofit kit to resolve this issue. The assembly manual is located below.

−	[[File:Pdf2.png\|link=http://www.bendtechdragon.com/files/anti_chatter_retrofit_assembly_manual.pdf]]'''[http://www.bendtechdragon.com/files/anti_chatter_retrofit_assembly_manual.pdf]'''	+	[[File:Pdf2.png\|link=http://www.bendtechdragon.com/files/anti_chatter_retrofit_assembly_manual.pdf]] '''[http://www.bendtechdragon.com/files/anti_chatter_retrofit_assembly_manual.pdf]'''

← Older revision		Revision as of 20:07, 24 March 2017
Line 78:		Line 78:
	- In some cases with older model 21 foot machines, some operators have experienced excessive chattering on the X-travel which has led to jagged or wavy cuts. If this unfortunate phenomenon has been the case for you, we suggest that you contact us and we will send out a retrofit kit to resolve this issue. The assembly manual is located below.		- In some cases with older model 21 foot machines, some operators have experienced excessive chattering on the X-travel which has led to jagged or wavy cuts. If this unfortunate phenomenon has been the case for you, we suggest that you contact us and we will send out a retrofit kit to resolve this issue. The assembly manual is located below.

−	[[File:Pdf2.png\|link=http://www.bendtechdragon.com/files/anti_chatter_retrofit_assembly_manual.pdf]] '''[http://www.bendtechdragon.com/files/anti_chatter_retrofit_assembly_manual.pdf]'''	+	[[File:Pdf2.png\|link=http://www.bendtechdragon.com/files/anti_chatter_retrofit_assembly_manual.pdf]]'''[http://www.bendtechdragon.com/files/anti_chatter_retrofit_assembly_manual.pdf]'''