Moving a Feature - Revision history

Fabcam1 at 15:59, 5 October 2015

2015-10-05T15:59:02Z

Fabcam1 at 21:13, 9 June 2014

2014-06-09T21:13:41Z

Fabcam1 at 19:51, 5 June 2014

2014-06-05T19:51:48Z

Fabcam1: Created page with "This is where we will move a feature on a part. This feature could be a bend or one of the two ends to any part. In our example we are going to move the one end point toward..."

2014-06-05T14:05:20Z

Created page with "This is where we will move a feature on a part. This feature could be a bend or one of the two ends to any part. In our example we are going to move the one end point toward..."

New page

This is where we will move a feature on a part. This feature could be a bend or one of the two ends to any part.

In our example we are going to move the one end point toward the ceiling a couple of inches.

MoveF1.png

Before we get started, create a PickPoint where the feature is going to move to. This is not needed if a PickPoint is already at the new location.

Step 1) Select the "Move Feature" command button:

MoveF2.png

Step 2) Select ANY PickPoint on the part you are going to adjust. We are only doing one thing with this step and that is to select the part. Select the easiest point to select the part.

MoveF3.png

Step 3) Select the PickPoint on the feature you want to move.

MoveF4.png

Step 4) Select the PickPoint the feature is moving to.

MoveF5.png

Bend-Tech will recalculate the part.

MoveF6.png

@@ Line 9: / Line 9: @@
 Before we get started, create a PickPoint where the feature is going to move to. This is not needed if a PickPoint is already at the new location.
-Step 1) Select the '''"Move Feature"''' command button:
+'''Step 1:''' Select the '''"Move Feature"''' command button:
 [[File:MoveF2.jpg]]
-Step 2)''' Select ANY PickPoint on the part you are going to adjust'''. We are only doing one thing with this step and that is to select the part. Select the easiest point to select the part.
+'''Step 2: Select ANY PickPoint on the part you are going to adjust'''. We are only doing one thing with this step and that is to select the part. Select the easiest point to select the part.
 [[File:MoveF3.jpg]]
-Step 3) Select the PickPoint on the feature you want to move.
+'''Step 3:''' Select the PickPoint on the feature you want to move.
 [[File:MoveF4.jpg]]
-Step 4) Select the PickPoint the feature is moving to.
+'''Step 4:''' Select the PickPoint the feature is moving to.
 [[File:MoveF5.jpg]]

@@ Line 4: / Line 4: @@
 In our example we are going to move the one end point toward the ceiling a couple of inches.
-MoveF1.png
+[[File:MoveF1.jpg]]
@@ Line 11: / Line 11: @@
 Step 1) Select the '''"Move Feature"''' command button:
-MoveF2.png
+[[File:MoveF2.jpg]]
 Step 2)''' Select ANY PickPoint on the part you are going to adjust'''. We are only doing one thing with this step and that is to select the part. Select the easiest point to select the part.
-MoveF3.png
+[[File:MoveF3.jpg]]
 Step 3) Select the PickPoint on the feature you want to move.
-MoveF4.png
+[[File:MoveF4.jpg]]
 Step 4) Select the PickPoint the feature is moving to.
-MoveF5.png
+[[File:MoveF5.jpg]]
 Bend-Tech will recalculate the part.
-MoveF6.png
+[[File:MoveF6.jpg]]