Moving a Part - Revision history

Fabcam1 at 15:50, 5 October 2015

2015-10-05T15:50:48Z

Fabcam1 at 21:12, 9 June 2014

2014-06-09T21:12:20Z

Fabcam1 at 19:50, 5 June 2014

2014-06-05T19:50:38Z

Fabcam1: Created page with "This section will show how to move a part in Assembly. In our example we are going to move the entire part toward the ceiling a couple of inches. MovePart1.png Before we g..."

2014-06-05T14:04:21Z

Created page with "This section will show how to move a part in Assembly. In our example we are going to move the entire part toward the ceiling a couple of inches. MovePart1.png Before we g..."

New page

This section will show how to move a part in Assembly.

In our example we are going to move the entire part toward the ceiling a couple of inches.

MovePart1.png

Before we get started, create a PickPoint where the part is going to move to. This is not needed if a PickPoint is already at the new location.

Step 1) Select the "Move Part" command button:

MovePart2.png

Step 2) Select ANY PickPoint on the part you are going to adjust. We are only doing one thing with this step and that is to select the part. Select the easiest point to select the part.

MovePart3.png

Step 3) Select the PickPoint on the part that will be the coupler location. This will be the point of the part that is anchored to the cursor while it's being moved.

MovePart4.png

Step 4) Select the PickPoint the part is moving to.

MovePart5.png

Bend-Tech will relocate the part.

MovePart6.png

@@ Line 8: / Line 8: @@
 Before we get started, create a PickPoint where the part is going to move to. This is not needed if a PickPoint is already at the new location.
-Step 1) Select the '''"Move Part"''' command button:
+'''Step 1:''' Select the '''"Move Part"''' command button:
 [[File:MovePart2.jpg]]
-Step 2)''' Select ANY PickPoint on the part you are going to adjust'''. We are only doing one thing with this step and that is to select the part. Select the easiest point to select the part.
+'''Step 2: Select ANY PickPoint on the part you are going to adjust'''. We are only doing one thing with this step and that is to select the part. Select the easiest point to select the part.
 [[File:MovePart3.jpg]]
-Step 3) '''Select the PickPoint on the part that will be the coupler location'''. This will be the point of the part that is anchored to the cursor while it's being moved.
+'''Step 3: Select the PickPoint on the part that will be the coupler location'''. This will be the point of the part that is anchored to the cursor while it's being moved.
 [[File:MovePart4.jpg]]
-Step 4)''' Select the PickPoint the part is moving to.'''
+'''Step 4: Select the PickPoint the part is moving to.'''
 [[File:MovePart5.jpg]]

@@ Line 3: / Line 3: @@
 In our example we are going to move the entire part toward the ceiling a couple of inches.
-MovePart1.png
+[[File:MovePart1.jpg]]
@@ Line 10: / Line 10: @@
 Step 1) Select the '''"Move Part"''' command button:
-MovePart2.png
+[[File:MovePart2.jpg]]
 Step 2)''' Select ANY PickPoint on the part you are going to adjust'''. We are only doing one thing with this step and that is to select the part. Select the easiest point to select the part.
-MovePart3.png
+[[File:MovePart3.jpg]]
 Step 3) '''Select the PickPoint on the part that will be the coupler location'''. This will be the point of the part that is anchored to the cursor while it's being moved.
-MovePart4.png
+[[File:MovePart4.jpg]]
 Step 4)''' Select the PickPoint the part is moving to.'''
-MovePart5.png
+[[File:MovePart5.jpg]]
 Bend-Tech will relocate the part.
-MovePart6.png
+[[File:MovePart6.jpg]]