Plate Tutorial - Revision history

Fabcam1 at 13:42, 28 September 2016

2016-09-28T13:42:10Z

2016-09-28T13:40:39Z

2016-04-01T21:32:02Z

2015-12-21T20:42:38Z

2015-12-16T20:30:15Z

2015-05-13T15:35:19Z

2015-03-05T19:59:21Z

2015-02-06T15:20:58Z

2015-01-22T20:07:17Z

2015-01-22T20:05:50Z

@@ Line 399: / Line 399: @@
 *To continue, create the new part.
-. Open a new part by clicking on the "'''New Plate'''" [[File:Plate_icon.png]] icon in the [Icon Menu Bar].
+. Open a new part by clicking on the "'''New Plate'''" [[File:Plate_icon.png]] icon in the [http://www.bend-tech.com/wiki7/index.php?title=Main_Menu_Bar#Toolbar.2FStatus_Bar Toolbar/Status Bar].
 [[File:W127.JPG]]

@@ Line 399: / Line 399: @@
 *To continue, create the new part.
-. Open a new part by clicking on the "'''New Plate'''" [[File:Plate_icon.png]] icon in the main toolbar.
+. Open a new part by clicking on the "'''New Plate'''" [[File:Plate_icon.png]] icon in the [Icon Menu Bar].
 [[File:W127.JPG]]

@@ Line 132: / Line 132: @@
 . There are two Add New buttons. Click the left one and type “'''.25 Inch'''” in the Material Name field.
-. Type "'''.25'''" in the thickness field (the field with the arrow pointing towards it in the picture below). Make sure '''Inches''' is selected in the Units area and click the Apply button.
+. Type "'''.25'''" in the thickness field (the field with the arrow pointing towards it in the picture below). Make sure '''Inches''' is selected in the Units area and click the Save button.
 *(Note) Make sure to "'''Save'''" this to the "'''Material List'''" in order to perform the next steps.

@@ Line 443: / Line 443: @@
 [[File:Trans_tut8.png]]
-. In this window, select the "'''Axis'''" [[File:Transfer_axis_button.png]] button and click the "'''Red'''" axes in the display area.
+. In this window, select the "'''Axis'''" [[File:Transfer_axis_button.png]] button and click the "'''Red'''" axis in the display area.
 . Then, click the "'''Rotate'''" [[File:Transfer_rotate_button.png]] button 3 times so the part is in the position seen in the picture below.

@@ Line 465: / Line 465: @@
 . Select the "'''OK'''" [[File:OK99.png]] button to close the window and finish the transfer.
-. Back in the Assembly designer, click on the green Pickpoint on the top of the first part to place the second part on top of it.
+. Now, minimize the Plate window and maximize the Assembly window.
 [[File:Trans_tut11.png]]

← Older revision		Revision as of 15:35, 13 May 2015
Line 38:		Line 38:

	3) For the purposes of this tutorial, click the "'''Maximize'''" button [[File:Min_Max_Close_Tab.png]] at the top right of the plate design window.		3) For the purposes of this tutorial, click the "'''Maximize'''" button [[File:Min_Max_Close_Tab.png]] at the top right of the plate design window.
−
−	~~4) Also, for the purposes of this tutorial, zoom out significantly by spinning the wheel on your mouse so that the Tri-star is about the size of a pea in the lower left corner of the display area.~~

	===Free Select===		===Free Select===

← Older revision		Revision as of 19:59, 5 March 2015
Line 1:		Line 1:
−	~~"'''UNDER CONSTRUCTION FOR ASSEMBLY TRANSFER: THANK YOU FOR YOUR PATIENCE'''"~~
−
	'''This tutorial is designed to walk you through the steps in creating a part using the sheet metal module.'''		'''This tutorial is designed to walk you through the steps in creating a part using the sheet metal module.'''
	__NOTOC__		__NOTOC__

@@ Line 356: / Line 356: @@
 [[File:W122.JPG]]
-. *Go to the "'''Definition'''" tab inside the "'''Part'''" tab. Select the "'''Define Flange'''" button and click the line on the far right side of Flange 3. In the "'''Display Mode'''" drop down menu in the toolbar, select "'''3D Shaded'''". Your part should look like the picture below.
+. To apply these holes, select the "'''Complete'''" button at the top of the display area.
 *Use the Display Mode menu to switch back to Design view when you are finished viewing the part.

@@ Line 445: / Line 445: @@
 [[File:Trans_tut8.png]]
-. In this window, select the "'''Axis'''" [[File:Transfer_Axis_Button.png]] button and click the "'''Red'''" axes in the display area.
+. In this window, select the "'''Axis'''" [[File:Transfer_axis_button.png]] button and click the "'''Red'''" axes in the display area.
-. Then, click the "'''Rotate'''" [[File:Transfer_Rotate_Button.png]] button 3 times so the part is in the position seen in the picture below.
+. Then, click the "'''Rotate'''" [[File:Transfer_rotate_button.png]] button 3 times so the part is in the position seen in the picture below.
 [[File:Trans_tut9.png]]
@@ Line 459: / Line 459: @@
 . Now, click the intersection of the 3 axes to set it as a reference and place the Pickpoint.
-. Click the "'''Apply'''" button and select the "'''Change Coupler'''" button.
+. Click the "'''Apply'''" button and select the "'''Change Coupler'''" [[File:Transfer_change_coupler.png]] button.
 . Select the new (green) Pickpoint in the display area to assign the coupler there.
@@ Line 465: / Line 465: @@
 [[File:Trans_tut13.png]]
-. Select the "'''OK'''" button to close the window and finish the transfer.
+. Select the "'''OK'''" [[File:OK99.png]] button to close the window and finish the transfer.
 . Back in the Assembly designer, click on the green Pickpoint on the top of the first part to place the second part on top of it.