SolidWorks Import Tutorial II - Revision history

Fabcam1 at 13:42, 22 September 2014

2014-09-22T13:42:53Z

Fabcam1 at 13:38, 22 September 2014

2014-09-22T13:38:03Z

Fabcam1 at 21:33, 18 September 2014

2014-09-18T21:33:38Z

Fabcam1 at 21:25, 18 September 2014

2014-09-18T21:25:39Z

Fabcam1 at 21:12, 18 September 2014

2014-09-18T21:12:31Z

Fabcam1 at 17:09, 18 September 2014

2014-09-18T17:09:42Z

Fabcam1 at 17:04, 18 September 2014

2014-09-18T17:04:48Z

Fabcam1 at 16:58, 18 September 2014

2014-09-18T16:58:08Z

Fabcam1 at 16:52, 18 September 2014

2014-09-18T16:52:56Z

Fabcam1 at 16:25, 18 September 2014

2014-09-18T16:25:06Z

@@ Line 1: / Line 1: @@
 __NOTOC__
@@ Line 26: / Line 25: @@
 ==Tutorial==
 ===Settings===
-*1. To begin, start up the "'''Bend-Tech 7x'''" program.
+. To begin, start up the "'''Bend-Tech 7x'''" program.
-*2. Before starting, we must first adjust some settings. [[File:ToolsOptionsSW1.png|right]] Go up to the Tools menu in the main menu bar. Click SW Plugin Settings in the drop down menu.
+. Before starting, we must first adjust some settings. [[File:ToolsOptionsSW1.png|right]] Go up to the Tools menu in the main menu bar. Click SW Plugin Settings in the drop down menu.
-*3. In the SW Plugin Settings window,  make sure Automatic Import is selected option under the Import Settings section. If not, click the circle next to Automatic Import to set it as the SolidWorks™ import method. Also, put checks in the checkboxes marked "'''Always Prompt for Material, Send Part to XYZ Interface and Show Results in Window'''". After these changes are made, click the Save button and then click Close. See picture below for clarification.
+. In the SW Plugin Settings window,  make sure Automatic Import is selected option under the Import Settings section. If not, click the circle next to Automatic Import to set it as the SolidWorks™ import method. Also, put checks in the checkboxes marked "'''Always Prompt for Material, Send Part to XYZ Interface and Show Results in Window'''". After these changes are made, click the Save button and then click Close. See picture below for clarification.
 * This window also provides the option to set a default template for exporting, to automatically find and import data, and to register the SW Plugin.
@@ Line 37: / Line 36: @@
 '''Bend-Tech SE vs. SW''': Bend-Tech SW contains all the functionality and features of Bend-Tech SE, as well as the ability to import parts directly from SolidWorks™. Any information available for Bend-Tech SE also applies to Bend-Tech SW.
 ===SolidWorks===
-*1. To be able to go through this tutorial, you must have a completed SolidWorks part file available. If not, create a part in SolidWorks™ and come back to this tutorial before continuing on.
+. To be able to go through this tutorial, you must have a completed SolidWorks part file available. If not, create a part in SolidWorks™ and come back to this tutorial before continuing on.
-*2. Once a part is ready, ensure that both SolidWorks™ and Bend-Tech are both open and running.
+. Once a part is ready, ensure that both SolidWorks™ and Bend-Tech are both open and running.
-*3. In SolidWorks™, select either the 3D Sketch or Sweep of the part from the Features list on the left side of the frame as shown below. Once selected the sweep or 3D sketch name will be highlighted in blue.
+. In SolidWorks™, select either the 3D Sketch or Sweep of the part from the Features list on the left side of the frame as shown below. Once selected the sweep or 3D sketch name will be highlighted in blue.
-*4. Once the sketch or sweep line has been selected, go up to the top left of the SolidWorks window and place your cursor over the right pointing arrow to access the menu bar. In the menu bar, go to the Bend-Tech option and click on Process Bend Info.
+. Once the sketch or sweep line has been selected, go up to the top left of the SolidWorks window and place your cursor over the right pointing arrow to access the menu bar. In the menu bar, go to the Bend-Tech option and click on Process Bend Info.
 [[File:SWBendInfo1.png]]
-*5. Once Process Bend Info has been selected, the Send To Bend-Tech panel will be opened on the left side of the window. Depending on what kind of feature you selected (3D Sketch or Sweep), it will be shown in either the Feature Selection or Sketch Selection box. Make sure that the listed feature is correct, click on it to select it, then click the green check button.
+. Once Process Bend Info has been selected, the Send To Bend-Tech panel will be opened on the left side of the window. Depending on what kind of feature you selected (3D Sketch or Sweep), it will be shown in either the Feature Selection or Sketch Selection box. Make sure that the listed feature is correct, click on it to select it, then click the green check button.
 [[File:SWSketchSend1.png]]  [[File:SWSweepSend1.png]]
 ===Part Definition===
-*1. Now, back in the Bend-Tech window it's time to import the part information. To do so, either click on the SolidWorks™ icon in the icon toolbar or go to File --> Import --> SolidWorks. This will bring the part information into a Bend-Tech Import Part window.
+. Now, back in the Bend-Tech window it's time to import the part information. To do so, either click on the SolidWorks™ icon in the icon toolbar or go to File --> Import --> SolidWorks. This will bring the part information into a Bend-Tech Import Part window.
 [[File:SWIcon.jpg]] [[File:File_Import_SW2.jpg]]
@@ Line 61: / Line 60: @@
 "'''(Note) If the material cannot be successfully tracked and imported, a message box (shown below) will appear. In this case, you need to manually import the part in the import window. Click Yes to open the Import interface. See the [[SolidWorks Import Tutorial#Part Definition | SolidWorks Tutorial - Part Definition Section]] for a step by step Import walkthrough. If you do not see this message box, proceed to the next step.'''"
-*2. A skeleton frame of the part will be shown in the part display window. Each section will have its own PickPoint. Straight sections have a gray outlined point and arcs/circles will have black outlined points.
+. A skeleton frame of the part will be shown in the part display window. Each section will have its own PickPoint. Straight sections have a gray outlined point and arcs/circles will have black outlined points.
 "'''Note: From now on, only one part will be shown in the images. Both parts (Exported using 3D Sketch or Sweep) are imported using the same methods.'''"
@@ Line 68: / Line 67: @@
-*3. Select a material from the "'''Select Material'''" drop down menu in the top corner. Since we are not working with the same part, you must choose a material that will work properly with your part design. If necessary, click the library button to open the "'''Tube/Pipe Library'''" to add or adjust any materials.
+. Select a material from the "'''Select Material'''" drop down menu in the top corner. Since we are not working with the same part, you must choose a material that will work properly with your part design. If necessary, click the library button to open the "'''Tube/Pipe Library'''" to add or adjust any materials.
 [[File:SWImportMaterial1.png]]
-*4. Next, select a die from the "'''Select Die'''" drop down menu. Notice how the imported CLR is listed directly below this drop down menu. Since this specific part has a 2 inch CLR, a 2.0 CLR die has been selected. Choose a die that is either close to the imported CLR or a die that you will be using when creating this part later on.
+. Next, select a die from the "'''Select Die'''" drop down menu. Notice how the imported CLR is listed directly below this drop down menu. Since this specific part has a 2 inch CLR, a 2.0 CLR die has been selected. Choose a die that is either close to the imported CLR or a die that you will be using when creating this part later on.
 [[File:SWImportDie1.png]]
-*5. Once the part has been successfully imported automatically, the "'''Part Details'''" window and an "'''XYZ Part'''" design window will be opened. In the XYZ Part design window, the part can be adjusted further, saved, or a setup sheet for the part can be printed. The import process is complete. Now, move on to the Part Details window.
+. Once the part has been successfully imported automatically, the "'''Part Details'''" window and an "'''XYZ Part'''" design window will be opened. In the XYZ Part design window, the part can be adjusted further, saved, or a setup sheet for the part can be printed. The import process is complete. Now, move on to the Part Details window.
 [[File:XYZPart79.jpg]]
-*6. In the Part Details window, the top part of the window is occupied by a text box containing information about the part. If necessary, you can type directly in this area to either change or add new information.
+. In the Part Details window, the top part of the window is occupied by a text box containing information about the part. If necessary, you can type directly in this area to either change or add new information.
 [[File:PartDetailsWindow78.jpg]]
-*7. The information and formatting displayed here is determined by the template that is currently in use. To change templates, select a new template from the drop down menu below "'''Default Template'''" in the SW Plugin Settings option.
+. The information and formatting displayed here is determined by the template that is currently in use. To change templates, select a new template from the drop down menu below "'''Default Template'''" in the SW Plugin Settings option.
-*8. Select the "'''Part Details'''" tab at the top of the screen to add some cut-off lengths. Type "'''5'''" into both the "'''Cut-Off Start'''" and "'''Cut-Off End'''" value fields. Notice how the cut length (if included in the template) will adjust to compensate for these values. The lengths in the LRA table (while in either mode) will also be affected by any values entered here.
+. Select the "'''Part Details'''" tab at the top of the screen to add some cut-off lengths. Type "'''5'''" into both the "'''Cut-Off Start'''" and "'''Cut-Off End'''" value fields. Notice how the cut length (if included in the template) will adjust to compensate for these values. The lengths in the LRA table (while in either mode) will also be affected by any values entered here.
 '''The tutorial is now complete.'''

@@ Line 32: / Line 32: @@
 *3. In the SW Plugin Settings window,  make sure Automatic Import is selected option under the Import Settings section. If not, click the circle next to Automatic Import to set it as the SolidWorks™ import method. Also, put checks in the checkboxes marked "'''Always Prompt for Material, Send Part to XYZ Interface and Show Results in Window'''". After these changes are made, click the Save button and then click Close. See picture below for clarification.
 [[File:SolidWSettings_open2.png]]
@@ Line 86: / Line 87: @@
-*7. The information and formatting displayed here is determined by the template that is currently in use. To change templates, select a new template from the drop down menu below Export Template in the bottom right corner.
+*7. The information and formatting displayed here is determined by the template that is currently in use. To change templates, select a new template from the drop down menu below "'''Default Template'''" in the SW Plugin Settings option.
-*8. Click the circle next to LRA to view the LRA table for the part instead of the export template information.
+'''The tutorial is now complete.'''

@@ Line 81: / Line 81: @@
-In the Part Details window, the top part of the window is occupied by a text box containing information about the part. If necessary, you can type directly in this area to either change or add new information.
+*6. In the Part Details window, the top part of the window is occupied by a text box containing information about the part. If necessary, you can type directly in this area to either change or add new information.
 [[File:PartDetailsWindow78.jpg]]
-The information and formatting displayed here is determined by the template that is currently in use. To change templates, select a new template from the drop down menu below Export Template in the bottom right corner.
+*7. The information and formatting displayed here is determined by the template that is currently in use. To change templates, select a new template from the drop down menu below Export Template in the bottom right corner.
 [[File:PartDetailsTemp82.jpg]]
-Click the circle next to LRA to view the LRA table for the part instead of the export template information.
+*8. Click the circle next to LRA to view the LRA table for the part instead of the export template information.
 [[File:PartDetailsLRA83.jpg]]
-While you're still in LRA mode, check the box next to Reversed LRA. The LRA table will now be reversed completely.
+*9. While you're still in LRA mode, check the box next to Reversed LRA. The LRA table will now be reversed completely.
 [[File:ReversedLRA84.jpg]]   [[File:LRAReversed.jpg]]
-Click the circle next to Custom Details to switch it back to the export template again. We are now going to add some cut-off lengths. In the Edit Part section, enter 5 into both the Cut-Off Start and Cut-Off End fields. Notice how the cut length (if included in the template) will adjust to compensate for these values. The lengths in the LRA table (while in either mode) will also be affected by any values entered here.
+*10. Click the circle next to Custom Details to switch it back to the export template again. We are now going to add some cut-off lengths. In the Edit Part section, enter 5 into both the Cut-Off Start and Cut-Off End fields. Notice how the cut length (if included in the template) will adjust to compensate for these values. The lengths in the LRA table (while in either mode) will also be affected by any values entered here.
 [[File:CutLength85.jpg]]
-Click the Copy button. The information shown (only export template) in the part details area will be copied to your clipboard and can be pasted anywhere.
+*11. Click the Copy button. The information shown (only export template) in the part details area will be copied to your clipboard and can be pasted anywhere.
 [[File:PartDetailsCopy86.jpg]]

← Older revision		Revision as of 21:25, 18 September 2014
Line 83:		Line 83:
	In the Part Details window, the top part of the window is occupied by a text box containing information about the part. If necessary, you can type directly in this area to either change or add new information.		In the Part Details window, the top part of the window is occupied by a text box containing information about the part. If necessary, you can type directly in this area to either change or add new information.

−	[[File:~~PartDetailsWindow81~~.jpg]]	+	[[File:PartDetailsWindow78.jpg]]

@@ Line 64: / Line 64: @@
 "'''Note: From now on, only one part will be shown in the images. Both parts (Exported using 3D Sketch or Sweep) are imported using the same methods.'''"
-[[File:SW_Window.jpg]]
+[[File:SW_Window23.jpg]]
@@ Line 78: / Line 78: @@
 *5. Once the part has been successfully imported automatically, the "'''Part Details'''" window and an "'''XYZ Part'''" design window will be opened. In the XYZ Part design window, the part can be adjusted further, saved, or a setup sheet for the part can be printed. The import process is complete. Now, move on to the Part Details window.
-[[File:XYZPart80.jpg]]
+[[File:XYZPart79.jpg]]

← Older revision		Revision as of 17:09, 18 September 2014
Line 78:		Line 78:
	*5. Once the part has been successfully imported automatically, the "'''Part Details'''" window and an "'''XYZ Part'''" design window will be opened. In the XYZ Part design window, the part can be adjusted further, saved, or a setup sheet for the part can be printed. The import process is complete. Now, move on to the Part Details window.		*5. Once the part has been successfully imported automatically, the "'''Part Details'''" window and an "'''XYZ Part'''" design window will be opened. In the XYZ Part design window, the part can be adjusted further, saved, or a setup sheet for the part can be printed. The import process is complete. Now, move on to the Part Details window.

−	[[File:XYZPart80.jpg~~\|500px~~]]	+	[[File:XYZPart80.jpg]]

@@ Line 28: / Line 28: @@
 *1. To begin, start up the "'''Bend-Tech 7x'''" program.
-*2. Before starting, we must first adjust some settings. [[File:ToolsOptionsSW1.png|right]] Go up to the Tools menu in the main menu bar. Click SW Plugin Settings in the drop down menu. In the SW Plugin Settings window
+*2. Before starting, we must first adjust some settings. [[File:ToolsOptionsSW1.png|right]] Go up to the Tools menu in the main menu bar. Click SW Plugin Settings in the drop down menu.
 *3. In the SW Plugin Settings window,  make sure Manual Import is the only selected option under the Import Settings section. If not, click the circle next to Manual Import to set it as the SolidWorks™ import method. If any changes were made, click the Save button and then click Close.