Tube/Pipe Library - Revision history

Fabcam1 at 16:41, 10 May 2018

2018-05-10T16:41:12Z

2018-05-10T16:40:46Z

2018-05-10T16:40:14Z

2017-11-14T19:14:34Z

2017-11-14T19:13:40Z

2017-06-27T14:20:53Z

2017-06-02T15:31:30Z

2016-07-20T18:47:29Z

2016-07-20T18:47:06Z

2016-06-22T21:47:58Z

@@ Line 84: / Line 84: @@
 '''Reserved for Dragon machine owners only, this will be the default widths, heights and lengths of all tabs and slots created in the software with this selected material.'''
-[[File:Slot_Tab0_Example1.jpg|500px|left]]
+[[File:Slot_Tab0_Example1.jpg|right]]
 *'''Tab Width:''' Enter the width of the intended tab in this value field.

@@ Line 84: / Line 84: @@
 '''Reserved for Dragon machine owners only, this will be the default widths, heights and lengths of all tabs and slots created in the software with this selected material.'''
-[[File:Slot_Tab0_Example1.jpg]]
+[[File:Slot_Tab0_Example1.jpg|500px|left]]
 *'''Tab Width:''' Enter the width of the intended tab in this value field.

@@ Line 83: / Line 83: @@
 [[File:Tube_Library_Slot_N_Tab1.png|right]]
 '''Reserved for Dragon machine owners only, this will be the default widths, heights and lengths of all tabs and slots created in the software with this selected material.'''
 *'''Tab Width:''' Enter the width of the intended tab in this value field.

@@ Line 2: / Line 2: @@
 __NOTOC__
-[[File:PRO_tube_library_1.png|right]]
+[[File:tube_library_1.png|right]]
 [[File:tube_library_3.png|left|150px]]The Tube/Pipe Library holds all the materials that can be used to create single parts. On the right side of the Tube/Pipe Library window, under 'Material List', is the list of each available material. To the right of this list is the area where tube/pipe material information will be shown.

@@ Line 2: / Line 2: @@
 __NOTOC__
-[[File:tube_library_1.png|right]]
+[[File:PRO_tube_library_1.png|right]]
 [[File:tube_library_3.png|left|150px]]The Tube/Pipe Library holds all the materials that can be used to create single parts. On the right side of the Tube/Pipe Library window, under 'Material List', is the list of each available material. To the right of this list is the area where tube/pipe material information will be shown.

@@ Line 88: / Line 88: @@
 *'''Slot Minimum Height:''' Enter the minimum height of the intended slot in this value field.
-*'''Tab Length Offset:''' Enter the length the tab will extend past the adjoining slot's inner wall (may be negative).
+*'''Tab Length Offset:''' Enter the length the tab as it will extend past the adjoining slot's inner wall (may be negative). This value is an offset for the length of the tab. With no offset (zero) the tab will extend into the adjoining tube until it is flush with the inner wall. If you do not wish for the tab to extend that far, you can use a negative offset. A positive offset would mean the tab would extend beyond the inside wall.
-*'''Slot Width Offset:''' Enter the amount to oversize the slot in reference to the adjoining tube's tab.
+*'''Slot Width Offset:''' Enter the amount to oversize the slot in reference to the adjoining tube's tab. This value will allow you to oversize the width of the hole (slot) on the adjoining tube. With no offset, the hole will be that same width as the tab. By adding a positive offset, the hole can be enlarged to allow an easier fit. This value will only affect the width of the hole, not the height.

← Older revision		Revision as of 18:47, 20 July 2016
Line 90:		Line 90:
	*'''Tab Length Offset:''' Enter the length the tab will extend past the adjoining slot's inner wall (may be negative).		*'''Tab Length Offset:''' Enter the length the tab will extend past the adjoining slot's inner wall (may be negative).

−	*'''Slot Width Offset:''' Enter the amount ~~you wish~~ to oversize the slot in reference to the adjoining tube's tab.	+	*'''Slot Width Offset:''' Enter the amount to oversize the slot in reference to the adjoining tube's tab.

@@ Line 82: / Line 82: @@
 <h2>Slot & Tab Settings</h2>
 [[File:Tube_Library_Slot_N_Tab1.png|right]]
-'''This will be the default widths, heights and lengths of all tabs and slots created in the software.'''
+'''This will be the default widths, heights and lengths of all tabs and slots created in the software with this selected material.'''
 *'''Tab Width:''' Enter the width of the intended tab in this value field.