XYZ Example 3 (Over 90 Degree Bends) - Revision history

Fabcam1 at 15:41, 27 June 2014

2014-06-27T15:41:51Z

Fabcam1 at 21:49, 9 June 2014

2014-06-09T21:49:53Z

Fabcam1 at 20:59, 5 June 2014

2014-06-05T20:59:49Z

Fabcam1: Created page with "In this example, we will show you how to create a closed "L" bracket. NOTE: All XYZ locations are based upon a 0,0,0 global location. Which means that each location is refere..."

2014-06-05T14:44:38Z

Created page with "In this example, we will show you how to create a closed "L" bracket. NOTE: All XYZ locations are based upon a 0,0,0 global location. Which means that each location is refere..."

New page

In this example, we will show you how to create a closed "L" bracket.

NOTE: All XYZ locations are based upon a 0,0,0 global location. Which means that each location is referenced to an absolute location. The start point does NOT need to be 0,0,0.

While in the XYZ interface:

1) Zero out the "Start" row to make our start point the center of the locator.

XYZex3.1.png

2) In the "Bend 1" row enter "12" for "X", and "0" for both "Y" and "Z". - This will give us 12" from the start of the tube, to the apex of the bend.

XYZex3.2.png

3) In the "End" row enter "2" for "X", "10" for "Y", and "0" for "Z". - From the apex of the bend, this will put our third point -10 back up the X axis and +10 down the Y axis.

XYZex3.3.png

@@ Line 7: / Line 7: @@
 ) Zero out the '''"Start"''' row to make our start point the center of the locator.
-[[:FileXYZex3.1.jpg]]
+[[File:XYZex3.1.jpg|800px]]
 ) In the '''"Bend 1"''' row enter '''"12"''' for '''"X"''', and '''"0"''' for both '''"Y" and "Z"'''. - This will give us 12" from the start of the tube, to the apex of the bend.
-[[File:XYZex3.2.jpg]]
+[[File:XYZex3.2.jpg|800px]]
 ) In the''' "End"''' row enter '''"2"''' for '''"X"''',''' "10"''' for '''"Y"''', and '''"0"''' for '''"Z"'''. - From the apex of the bend, this will put our third point -10 back up the X axis and +10 down the Y axis.
-[[File:XYZex3.3.jpg]]
+[[File:XYZex3.3.jpg|800px]]

@@ Line 7: / Line 7: @@
 ) Zero out the '''"Start"''' row to make our start point the center of the locator.
-XYZex3.1.png
+[[:FileXYZex3.1.jpg]]
 ) In the '''"Bend 1"''' row enter '''"12"''' for '''"X"''', and '''"0"''' for both '''"Y" and "Z"'''. - This will give us 12" from the start of the tube, to the apex of the bend.
-XYZex3.2.png
+[[File:XYZex3.2.jpg]]
 ) In the''' "End"''' row enter '''"2"''' for '''"X"''',''' "10"''' for '''"Y"''', and '''"0"''' for '''"Z"'''. - From the apex of the bend, this will put our third point -10 back up the X axis and +10 down the Y axis.
-XYZex3.3.png
+[[File:XYZex3.3.jpg]]

@@ Line 1: / Line 1: @@
 In this example, we will show you how to create a closed "L" bracket.
-NOTE: All XYZ locations are based upon a 0,0,0 global location. Which means that each location is referenced to an absolute location. The start point does NOT need to be 0,0,0.
+'''NOTE: All XYZ locations are based upon a 0,0,0 global location. Which means that each location is referenced to an absolute location. The start point does NOT need to be 0,0,0.'''
 While in the XYZ interface:
-) Zero out the "Start" row to make our start point the center of the locator.
+) Zero out the '''"Start"''' row to make our start point the center of the locator.
 XYZex3.1.png
-) In the "Bend 1" row enter "12" for "X", and "0" for both "Y" and "Z". - This will give us 12" from the start of the tube, to the apex of the bend.
+) In the '''"Bend 1"''' row enter '''"12"''' for '''"X"''', and '''"0"''' for both '''"Y" and "Z"'''. - This will give us 12" from the start of the tube, to the apex of the bend.
 XYZex3.2.png
-) In the "End" row enter "2" for "X", "10" for "Y", and "0" for "Z". - From the apex of the bend, this will put our third point -10 back up the X axis and +10 down the Y axis.
+) In the''' "End"''' row enter '''"2"''' for '''"X"''',''' "10"''' for '''"Y"''', and '''"0"''' for '''"Z"'''. - From the apex of the bend, this will put our third point -10 back up the X axis and +10 down the Y axis.
 XYZex3.3.png