Motor Sports Templates II

...Motor Sports Templates Continued.

For initial information on MSP Templates, see Motor Sport Templates.

Mounts Category

• The fourth button in the "Style of Plate" section is for Shackles, Mounts, and Plates style projects.

Spare Tire Mount

Current Template Values:

• The distance labeled "L1" (default 1) is the length from the center of the middle hole to the center of the stud holes.
• The distance labeled "D1" (default 5) is the length of the diameter of the outside edge of the part.
• The distance labeled "D2" (default 3) is the length of the diameter of the center hole.
• The distance labeled "D3" (default .5) is the length of the diameter of the stud holes.
• The pink "#" is the number of stud holes the user would like to create circling the part.

Tube Tab

Current Template Values:

• The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
• The distance labeled "R1" (default 1) is the length from the center of the top hole to the top arc.
• The distance labeled "R2" (default 2) is the length from the center of the bottom hole to the bottom arc.
• The distance labeled "D1" (default 5) is the length of the diameter of the top hole.
• The distance labeled "D2" (default 3) is the length of the diameter of the bottom hole.

Bolt Lock

Current Template Values:

• The distance labeled "L1" (default 3) is the length from the center of the top hole to the center of the bottom hole.
• The distance labeled "L2" (default .75) is the length of the diameter of the inner edge of the top hole.
• The distance labeled "R1" (default 1) is the length from the center of the top hole to the top arc.
• The distance labeled "R2" (default .5) is the length from the center of the bottom hole to the bottom arc.
• The distance labeled "D1" (default .25) is the length of the diameter of the bottom hole.

Shackle 2 Hole

Current Template Values:

• The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
• The distance labeled "R1" (default 1) is the length from the center of the top hole to the top arc, or from the center of the bottom hole to the bottom arc.
• The distance labeled "D1" (default .5) is the length of the diameter either the top or bottom hole.

Shackle 3 Hole

Current Template Values:

• The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
• The distance labeled "L2" (default 2.5) is the length from the center of the middle hole to the center of the bottom hole.
• The distance labeled "R1" (default 1) is the length from the center of the top hole to the top arc, or from the center of the bottom hole to the bottom arc.
• The distance labeled "D1" (default .5) is the length of the diameter either the top or bottom hole.
• The distance labeled "D2" (default 1) is the length of the diameter of the middle hole.

Shackle 2 Hole - Offset

Current Template Values:

• The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
• The distance labeled "L2" (default 1) is the width of the part as a whole.
• The distance labeled "L3" (default 2) is the length from the bottom of the part to the lowest bend.
• The distance labeled "L4" (default .5) is the length of the offset between the top half of the part and the bottom half.
• The distance labeled "D1" (default .5) is the length of the diameter of either the top or bottom hole.

Shackle 3 Hole - Offset

Current Template Values:

• The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
• The distance labeled "L2" (default 1) is the width of the part as a whole.
• The distance labeled "L3" (default 1.5) is the length for the center of the top hole to the center of the middle hole.
• The distance labeled "L4" (default 2) is the length from the bottom of the part to the lowest bend.
• The distance labeled "L5" (default .5) is the length of the offset between the top half of the part and the bottom half.
• The distance labeled "D1" (default .25) is the length of the diameter of either the top or bottom hole.
• The distance labeled "D2" (default .5) is the length of the diameter of the middle hole.

Oval Mount

Current Template Values:

• The distance labeled "L1" (default ) is the length from the center of the top hole to the center of the middle hole.
• The distance labeled "R1" (default ) is the length from the center of the top hole to the top arc, or from the center of the bottom hole to the bottom arc.
• The distance labeled "R2" (default ) is the length from the center of the middle hole to the left and right arcs.
• The distance labeled "D1" (default ) is the length of the diameter of the middle hole.
• The distance labeled "D2" (default ) is the length of the diameter of either the top or bottom hole.

Mount 2 Hole

Current Template Values:

• The value labeled "A1" (default 60) is the angle of the outside of the part.
• The distance labeled "L1" (default 3) is the width of the bottom of the part.
• The distance labeled "L2" (default 1.5) is the height of the part as a whole.
• The distance labeled "L3" (default .75) is the length for the center of the top left hole to the center of the top right hole.
• The distance labeled "L4" (default .375) is the length from the center of either hole to the top of the part.
• The distance labeled "R1" (default .125) is the size of the bottom arcs.
• The distance labeled "R2" (default .25) is the size of the top arcs.
• The distance labeled "D1" (default .25) is the length of the diameter of the holes.

Mount 2 Hole Cutout

Current Template Values:

• The value labeled "A1" (default 60) is the angle of the outside of the part.
• The distance labeled "L1" (default 3) is the width of the bottom of the part.
• The distance labeled "L2" (default 1.5) is the height of the part as a whole.
• The distance labeled "L3" (default .75) is the length for the center of the top left hole to the center of the top right hole.
• The distance labeled "L4" (default .375) is the length from the center of either hole to the top of the part.
• The distance labeled "L5" (default .5) is the vertical length of the gap on the bottom of the part.
• The distance labeled "L6" (default 1) is the horizontal length of the gap on the bottom of the part.
• The distance labeled "R1" (default .125) is the size of the bottom arcs.
• The distance labeled "R2" (default .25) is the size of the top arcs.
• The distance labeled "D1" (default .25) is the length of the diameter of the holes.

Master Cylinder Mount

Current Template Values:

• The distance labeled "L1" (default 3) is the width of the bottom of the part.
• The distance labeled "L2" (default 2) is the vertical height from the bottom of the part to the center of any hole.
• The distance labeled "R1" (default 1) is the size of the top arc.
• The distance labeled "R2" (default .5) is the size of the side arcs.
• The distance labeled "D1" (default 1) is the length of the diameter of the middle hole.
• The distance labeled "D2" (default .25) is the length of the diameter of the outer holes.

Through Plate

Current Template Values:

• The distance labeled "L1" (default 2) is the horizontal and vertical length from the center of the middle hole to the center of any other hole.
• The distance labeled "R1" (default 1) is the length from the center of any outer hole to its arc.
• The distance labeled "D1" (default 1) is the length of the diameter of the middle hole.
• The distance labeled "D2" (default .25) is the length of the diameter of any outer holes.

Square Mount

Current Template Values:

• The distance labeled "L1" (default 2) is the horizontal and vertical length from the center of the middle hole to the center of any other hole.
• The distance labeled "R1" (default 1) is the length from the center of any outer hole to its arc.
• The distance labeled "D1" (default 1) is the length of the diameter of the middle hole.
• The distance labeled "D2" (default .25) is the length of the diameter of any outer holes.

Mount 4 Hole

Current Template Values:

• The distance labeled "L1" (default 2) is the width of the whole part.
• The distance labeled "L2" (default 3) is the height of the whole part.
• The distance labeled "L3" (default .5) is the length from the center of any hole to the closest outer edge of the part.
• The distance labeled "R1" (default 1) is the length from the center of any outer hole to its arc.
• The distance labeled "D1" (default .25) is the length of the diameter of any outer holes.

Cutout 4 Hole

Current Template Values:

• The distance labeled "L1" (default 2) is the width of the whole part.
• The distance labeled "L2" (default 3) is the height of the whole part.
• The distance labeled "L3" (default .375) is the length from the center of any hole to the closest outer edge of the part.
• The distance labeled "L4" (default .75) is the height of the section from either the bottom edge to the inner edge, or the top edge to the inner edge.
• The distance labeled "L5" (default .5) is the width of the section from the left edge to the inner edge, or the right edge to the inner edge.
• The distance labeled "R1" (default .5) is the length from the center of any outer hole to its arc.
• The distance labeled "R2" (default .25) is the size of the inner arcs.
• The distance labeled "D1" (default .25) is the length of the diameter of any outer holes.

Mounting Bracket Flat

Current Template Values:

• The distance labeled "L1" (default 4) is the height of the whole part.
• The distance labeled "L2" (default 2) is the inside width of the whole part.
• The distance labeled "L3" (default 1) is the outside depth of the part's side flanges.
• The distance labeled "L4" (default 2) is the height from the bottom edge to the center of the bottom hole.
• The distance labeled "L5" (default 1) is the length from the center of the top hole to the center of the bottom hole.
• The distance labeled "D1" (default .75) is the length of the diameter of the holes.

Mounting Bracket Angled

Current Template Values:

• The distance labeled "L1" (default 4) is the height of the whole part.
• The distance labeled "L2" (default 2) is the inside width of the whole part.
• The distance labeled "L3" (default 1) is the outside depth of the part's side flanges at the top. (This distance determines the part's angle.)
• The distance labeled "L4" (default 2) is the height from the bottom edge to the center of the bottom hole.
• The distance labeled "L5" (default 1) is the length from the center of the top hole to the center of the bottom hole.
• The distance labeled "D1" (default .75) is the length of the diameter of the holes.

Gusset Category

• The fifth button in the "Style of Plate" section is for Gussets style projects.

Gusset

Current Template Values:

• The value labeled "A1" (default 90) is the angle of the outside of the part.
• The value labeled "A2" (default 120) is the angle of the inside of the part.
• The distance labeled "L1" (default 4) is the width of the part from end to end.
• The distance labeled "R1" (default 1) is the length from the center of the part to the outer arc.
• The distance labeled "R2" (default .25) is the size of the leg's outer arcs.

Gusset Cutout

Current Template Values:

• The value labeled "A1" (default 90) is the angle of the outside of the part.
• The distance labeled "L1" (default 4) is the width of the part from end to end.
• The distance labeled "L2" (default .5) is the width of the section from either the bottom edge to the inner edge, or the right edge to the inner edge.
• The distance labeled "L3" (default .5) is the width of the section from the diagonal outer edge to the inner edge.
• The distance labeled "R1" (default 1) is the length from the inner section of the part to the outer arc.
• The distance labeled "R2" (default .25) is the size of the leg's outer arcs.
• The distance labeled "R3" (default .1) is the size of the leg's inner arcs.

Gusset 1 Hole

Current Template Values:

• The value labeled "A1" (default 90) is the angle of the outside of the part.
• The distance labeled "L1" (default 4) is the height of the part from top to bottom.
• The distance labeled "L2" (default 1) is the length from the center of the part to the inner arc.
• The distance labeled "R1" (default 1) is the length from the center of the part to the outer arc.
• The distance labeled "R2" (default .25) is the size of the leg's outer arcs.
• The distance labeled "R3" (default 4) is the size of the inner arc.
• The distance labeled "D1" (default 1) is the length of the diameter of the middle hole.

Gusset 2 Hole

Current Template Values:

• The value labeled "A1" (default 90) is the angle of the outside of the part.
• The distance labeled "L1" (default 4) is the width of the part from end to end.
• The distance labeled "L2" (default .5) is the width of the section from either the bottom edge to the center of the bottom hole, or the right edge to the center of the right hole.
• The distance labeled "L3" (default 1.5) is the length from one hole's center to the other.
• The distance labeled "R1" (default 1) is the length from the inner section of the part to the outer arc.
• The distance labeled "R2" (default .25) is the size of the leg's outer arcs.
• The distance labeled "R3" (default 4) is the size of the inner arc.
• The distance labeled "D1" (default 1) is the length of the diameter of either hole.

Gusset 5 Hole

Current Template Values:

• The value labeled "A1" (default 90) is the angle of the outside of the part.
• The value labeled "A2" (default 120) is the angle of the inside of the part.
• The distance labeled "L1" (default 4) is the height of the part from top to bottom.
• The distance labeled "L2" (default .5) is the length of the section on the outer edge where the legs meet.
• The distance labeled "L3" (default .25) is the length from any outer edge to the closest edge of any hole.
• The distance labeled "L4" (default .75) is the length from the center of the "D1" hole to the center of either "D2" holes.
• The distance labeled "L5" (default 1) is the length from the center of either "D3" hole to the edge of the closest leg's arc
• The distance labeled "R1" (default .25) is the size of the leg's outer arcs.
• The distance labeled "D1" (default .75) is the length of the diameter of the middle hole.
• The distance labeled "D2" (default .5) is the length of the diameter of the inner most holes.
• The distance labeled "D3" (default .25) is the length of the diameter of the outer most holes.

Gusset Webbed

Current Template Values:

• The value labeled "A1" (default 90) is the angle of the outside of the part.
• The distance labeled "L1" (default 4) is the height of the part from top to bottom.
• The distance labeled "L2" (default 3) is the length from the outer arc "R2" to where the inner arcs "R1" meet.
• The distance labeled "R1" (default 3) is the size of the two inner arcs.
• The distance labeled "R2" (default .5) is the size of the outer arc.

Gusset Taco

Current Template Values:

• The value labeled "A1" (default 90) is the angle of the two fold edges of the part.
• The distance labeled "L1" (default 2) is the width of the part from end to end.
• The distance labeled "D1" (default 1) is the diameter of the rounded edge of the part.

Suspension/Traction Mounts Category

• The sixth button in the "Style of Plate" section is for "Suspension Mounts and Traction Bar Mounts" style projects.

Buggy Link (lower)

Current Template Values:

• The distance labeled "L1" (default 3) is the width of the part from end to end.
• The distance labeled "L2" (default 4) is the height of the part.
• The distance labeled "L3" (default 1.5) is the length from the top to the bottom of the "R2" arcs in the top hole.
• The distance labeled "L4" (default .5) is the length from the bottom edge of the part to the center of the "D1" holes.
• The distance labeled "L5" (default 1) is the length from the center of one "D1" hole to another.
• The distance labeled "R1" (default 1) is the size of the top outer arc.
• The distance labeled "R2" (default .5) is the size of the top hole's inner arc.
• The distance labeled "R3" (default .25) is the size of the bottoms corner's arcs.
• The distance labeled "D1" (default .5) is the length of the diameter of each of the bottom holes.

Buggy Link (upper)

Current Template Values:

• The distance labeled "L1" (default 4) is the width of the part from end to end.
• The distance labeled "L2" (default 4) is the height of the part.
• The distance labeled "L3" (default 1.5) is the length from the top to the bottom of the "R2" arcs in the top hole.
• The distance labeled "L4" (default .5) is the length from the bottom edge of the part to the center of the "D1" holes.
• The distance labeled "L5" (default 1) is the length from the center of one "D1" hole to another.
• The distance labeled "R1" (default 1) is the size of the top outer arc.
• The distance labeled "R2" (default .5) is the size of the top hole's inner arc.
• The distance labeled "R3" (default .375) is the size of the bottoms corner's arcs.
• The distance labeled "D1" (default .25) is the length of the diameter of each of the bottom holes.

Rod End Clevis

Current Template Values:

• The distance labeled "L1" (default 2) is the width of the part from end to end.
• The distance labeled "L2" (default 3) is the length of the part from the center of the hole to the bottom edge.
• The distance labeled "R1" (default .75) is the size of each of the hole's inner arcs.
• The distance labeled "D1" (default .5) is the length of the diameter of each of the holes.
• The distance labeled "D2" (default 1) is the length of the diameter of the bend between the two flanges.

Leaf Spring Hanger

Current Template Values:

• The value labeled "A1" (default 60) is the angle of the two fold edges of the part.
• The distance labeled "L1" (default 1) is the width of the part from end to end.
• The distance labeled "L2" (default 2) is the height of the part.
• The distance labeled "L3" (default 2) is the length from back to front.
• The distance labeled "L4" (default .5) is the length from the back edge of the part to the center of the "D1" holes.
• The distance labeled "L5" (default .5) is the length from the bottom edge of the part to the center of the "D1" hole.
• The distance labeled "R1" (default .25) is the size of the back outer arc.
• The distance labeled "R2" (default .25) is the size of the bottom front arc.
• The distance labeled "D1" (default .25) is the length of the diameter of the hole.

Adjustable Mount 3 Hole

Current Template Values:

• The distance labeled "L1" (default 4) is the width of the part from the bottom's end to end.
• The distance labeled "L2" (default 4) is the height of the part.
• The distance labeled "L3" (default .5) is the length from the bottom edge of the part to the center of the bottom holes.
• The distance labeled "L4" (default .75) is the length between the center of the "D1" holes.
• The distance labeled "R1" (default 1) is the size of the top hole's outer arc.
• The distance labeled "R2" (default .375) is the size of the bottom arcs.
• The distance labeled "D1" (default .25) is the length of the diameter of each of the bottom holes.
• The distance labeled "D2" (default 1) is the length of the diameter of the top hole.

Adjustable Mount 5 Hole

Current Template Values:

• The distance labeled "L1" (default 4) is the width of the part from the bottom's end to end.
• The distance labeled "L2" (default 4) is the height of the part.
• The distance labeled "L3" (default .5) is the length from the bottom edge of the part to the center of the bottom holes.
• The distance labeled "L4" (default .75) is the length between the center of the "D1" holes.
• The distance labeled "R1" (default 1) is the size of the top hole's outer arc.
• The distance labeled "R2" (default .375) is the size of the bottom arcs.
• The distance labeled "D1" (default .25) is the length of the diameter of each of the bottom holes.
• The distance labeled "D2" (default 1) is the length of the diameter of the top hole.

ETC Category

• The seventh button in the "Style of Plate" section is for projects that don't fall into any specific category.

Tie Down Tab 1

Current Template Values:

• The value labeled "A1" (default 30) is the angle of the left side of the part.
• The value labeled "A2" (default 90) is the angle of the top side of the part.
• The distance labeled "L1" (default 6) is the width of the part from end to end.
• The distance labeled "L2" (default 1) is the width of the left section of the part.
• The distance labeled "L3" (default 1) is the width of the right section of the part.
• The distance labeled "R1" (default 1) is the size of the top outer arc.
• The distance labeled "R2" (default .5) is the size of the bottom inner arc.

Tie-Down Tab 2

Current Template Values:

• The distance labeled "L1" (default 1) is the width of the vertical cross section.
• The distance labeled "L2" (default 1) is the height of the horizontal cross section.
• The distance labeled "L3" (default 1) is the vertical length from the top of the part to the top of the horizontal cross section, or from the bottom of the part to the bottom of the horizontal cross section.
• The distance labeled "L4" (default 1) is the horizontal length from the left edge of the part to the left edge of the horizontal cross section, or from the right edge of the part to the right edge of the horizontal cross section.
• The distance labeled "R1" (default .25) is the size of the outer arcs.
• The distance labeled "R2" (default .25) is the size of the inner arcs.

Battery Box

Current Template Values:

• The distance labeled "L1" (default 4) is the width of the part as a whole.
• The distance labeled "L2" (default 3) is the depth of the part's left and right sides.
• The distance labeled "L3" (default 1) is the height of the left and right sides of the part.
• The distance labeled "L4" (default 2) is the height of the front and back sides of the part.

Utility Box

Current Template Values:

• The distance labeled "L1" (default 4) is the width of the part as a whole.
• The distance labeled "L2" (default 3) is the depth of the part's left and right sides.
• The distance labeled "L3" (default 2) is the height of the back side of the part.
• The distance labeled "L4" (default 1) is the height of the front side of the part.

Bottle Opener

Current Template Values:

• The distance labeled "L1" (default 4) is the length from the center of the part's hole to the edge of the handle.
• The distance labeled "L2" (default .75) is the length of the hole's straight edge.
• The distance labeled "L3" (default 1) is the width of the handle.
• The distance labeled "R1" (default .25) is the size of the handle's arcs.
• The distance labeled "D1" (default 1.5) is the length of the diameter of the outer edge of the hole.
• The distance labeled "D2" (default 1) is the length of the diameter of the of the inner edge of the hole.

New Motor Sports Templates will be updated periodically. Thank you.