Dragon Material Machine Settings

The Dragon Material Machine Settings page is meant to show the user how the Dragon machine reacts to your different material and tooling settings. These are general guidelines meant to give you understanding about your material machine settings and how they operate both within the software and in the practical application of the Dragon machine.

• To access the Material Machine Settings, first select the Tube/Pipe Library from the Dragon Task Menu Screen.

• After selecting a material from the Material List switch from the General tab to the Machine tab to access your Material Machine Settings.

Machine Settings

Basic Settings

Kerf Width:

• This is the size (width) of the cutting path determined by your plasma torch. This is generally between 0.05 and 0.06 depending on your plasma torch settings and type of torch you own. Consumables that you're using and amperage can change this number considerably, so we suggest a test in order to measure the exact width.

Minimum Web:

• This is the amount of material selected to be left between any nested parts. We recommend to set this number to 0.5 to indicate that a half of an inch will be left between these parts. This will help accommodate for lead-ins and lead-outs that may require this extra space.

Default Length:

• This section indicates your default stock length of tubing typically associated with this material. Every time you select this material, your stock length of tubing in your nesting projects will default to this number. This will be input in inches.

Cutting Overlap:

• This is the amount of under travel or over travel that a cut profile will perform. This can be changed under certain circumstances. One of which would be in order to leave a certain amount of material attaching your stock tube to the cut part in order to break it off after the cut is performed.

Text Size:

• This is the text size used for auto generated text (such as holesaw information). This text will not be seen under most circumstances. Default should be set to 1. This is the height of the text (in inches).

Feed Rates

Cutting Feed Rate:

• This setting determines the rate at which the machine's torch moves in the act of performing a cut. These feed rates are dependent on your particular torch and thickness of material, so be sure to check your Hypertherm manual for exact cutting feed rates. Links to manuals are located at the bottom of this page.

Marking Feed Rate:

• This is the rate at which the marker travels along the tubing. This can remain at 100 inches per minute to ensure a smooth like with the marker.

Engraving Feed Rate:

• This is the rate at which your engraver travels along the tube. This should be set to 30 inches per minute to ensure consistent engraving.

Height Offsets

Cutting Height:

• This is the number indicating how far off the tubing the torch head will be located during cutting. This height depends on the model of torch you have as well as the material thickness. Refer to your hypertherm manual for an exact height. Links to manuals are located at the bottom of this page.

Marking Height:

• This number is meant to adjust the calibration values correlated to the height the marker head. (Example) If the tubing was calibrated to show a 1.75 OD, but the actual OD is 1.74, then you may enter a -.01 in this field in order to compensate for the difference in tube diameter when marking.

Engraving Height:

• This number is meant to adjust the calibration values correlated to the height the engraver head. (Example) If the tubing was calibrated to show a 1.75 OD, but the actual OD is 1.74, then you may enter a -.01 in this field in order to compensate for the difference in tube diameter when engraving.

Torch Touch Off:

• This number is meant to adjust the calibration values correlated to the height the torch head. (Example) If the tubing was calibrated to show a 1.75 OD, but the actual OD is 1.74, then you may enter a -.01 in this field in order to compensate for the difference in tube diameter when cutting.

Pierce Height:

• This number will indicate the distance that the torch will be placed off of the tubing during the piercing process of a cut. This is always 2 1/2 times the cutting height. Refer to your hypertherm manual for an exact height. Links to manuals are located at the bottom of this page.

Ignite Settings

• These settings are completely user specified and can vary based on the user's preference.

Ignite Type:

• This is where the user will select the type of lead-in ignite type that will be set to this material by default. Arc with Angle is our preferred method. This means that the torch will initiate its cut into the material at an arc which will ease into the intended cut at an angle. This is a smooth ignite type and leaves little chance for error.

Angle/Sweep:

• This will be the angle at which the initial cut eases into the intended cut. We recommend a 45 degree angle for the ignite cut.

Dwell Time(sec):

• This indicates how long the torch will remain on one place during the pierce. This can differ based on your torch and material type and thickness. Refer to your hypertherm manual for an exact time. Links to manuals are located at the bottom of this page.

Radius:

• This is where the user will enter the radius of the arc that channels into the cut profile. We recommend keeping this at around .125 as a preference.

Length/Distance:

• This is the length of the line that eases into the actual cut profile. We can keep this relatively short. We recommend .125 in most cases.

Extinguish Settings:

• These settings are completely user specified and can vary based on the user's preference.

Extinguish Type:

• This is where the user will select the type of lead-out extinguish type that will be set to this material by default. Perpendicular is our preferred method. This means that the torch will extinguish its cut at a perpendicular angle after the cut profile has been performed. This is a smooth extinguish type that leaves the cut profile smoothly.

Angle/Sweep:

• Opposite of the ignite type section, this will be the angle at which the cut eases out of the intended cut. This will be greyed out if the extinguish type is set to perpendicular.

Dwell Time(sec):

• This indicates how long the torch will remain on one place during the extinguishing stage of the torch. This can be set to 0.

Radius:

• This is where the user will enter the radius of the arc that channels out the cut profile. We recommend keeping this at around .125 as a preference.

Length/Distance:

• This is the length of the line that eases out of the cut profile. We can keep this relatively short. We recommend .125 in most cases.

Hypertherm Manual Links

Hypertherm Powermax 45 Manual

Hypertherm Powermax 65-86 Manual

MRT Duramax Retrofit for 100-1250-1650 Manual

MRT2 Duramax Retrofit for 600-800-900