Difference between revisions of "How To Use Cutting Wrappers"
(Created page with "Line up the Templates The templates have 2 calibration lines on them. One is for rotation alignment and the other is for location down the tube. Cutting1.jpg There are 3 d...") |
|||
| Line 1: | Line 1: | ||
| − | Line up the Templates | + | '''Line up the Templates''' |
The templates have 2 calibration lines on them. One is for rotation alignment and the other is for location down the tube. | The templates have 2 calibration lines on them. One is for rotation alignment and the other is for location down the tube. | ||
| Line 8: | Line 8: | ||
There are 3 different setups for the templates: | There are 3 different setups for the templates: | ||
| − | Straight tube, one end cut | + | '''Straight tube, one end cut''' |
| − | Straight tube, both ends cut | + | '''Straight tube, both ends cut''' |
| − | Bent tube, either end cut | + | '''Bent tube, either end cut''' |
| − | 1) Straight Tube, One End Cut: | + | '''1) Straight Tube, One End Cut:''' |
Cutting2.jpg | Cutting2.jpg | ||
| Line 26: | Line 26: | ||
| − | 2) Straight Tube, Both Ends Cut: | + | '''2) Straight Tube, Both Ends Cut:''' |
Cutting4.jpg | Cutting4.jpg | ||
| − | NOTE: The above pic shows cutting on both ends of the tube in the same picture. This is shown in the software as one end at a time. | + | '''NOTE: The above pic shows cutting on both ends of the tube in the same picture. This is shown in the software as one end at a time.''' |
| Line 39: | Line 39: | ||
| − | 3) Bent Tube, Either End Cut: | + | '''3) Bent Tube, Either End Cut:''' |
Cutting6.jpg | Cutting6.jpg | ||
| − | Line the rotary line with the out-most radius of the arc as shown in the following picture. The location line will depend on the check-box value of "Distance to Perp of Bend". | + | Line the rotary line with the out-most radius of the arc as shown in the following picture. The location line will depend on the check-box value of '''"Distance to Perp of Bend"'''. |
| − | If it is Distance to Perp is checked then you will come off of the Perp (apex for bends under 90 degrees) for the location line as shown in the following pic. | + | If it is '''Distance to Perp''' is checked then you will come off of the Perp (apex for bends under 90 degrees) for the location line as shown in the following pic. |
Cutting7.jpg | Cutting7.jpg | ||
| − | If Distance to Perp is not checked, it will be Distance to end. You will come off the end of the tube as shown in the next pic. | + | If '''Distance to Perp''' is not checked, it will be '''Distance to end.''' You will come off the end of the tube as shown in the next pic. |
Cutting8.jpg | Cutting8.jpg | ||
Revision as of 13:05, 5 June 2014
Line up the Templates
The templates have 2 calibration lines on them. One is for rotation alignment and the other is for location down the tube.
Cutting1.jpg
There are 3 different setups for the templates:
Straight tube, one end cut
Straight tube, both ends cut
Bent tube, either end cut
1) Straight Tube, One End Cut:
Cutting2.jpg
There is no rotary line up (blue line up line) and the location calibration (red line) needs to be placed the distance labeled from the opposite end. [21 3/16 in our case]
Cutting3.jpg
2) Straight Tube, Both Ends Cut:
Cutting4.jpg
NOTE: The above pic shows cutting on both ends of the tube in the same picture. This is shown in the software as one end at a time.
Line the rotary lines down the tube (blue line) and the location calibration (red line) needs to be placed at the distanced labeled from each other. [19 9/16 in our case]
Cutting5.jpg
3) Bent Tube, Either End Cut:
Cutting6.jpg
Line the rotary line with the out-most radius of the arc as shown in the following picture. The location line will depend on the check-box value of "Distance to Perp of Bend".
If it is Distance to Perp is checked then you will come off of the Perp (apex for bends under 90 degrees) for the location line as shown in the following pic.
Cutting7.jpg
If Distance to Perp is not checked, it will be Distance to end. You will come off the end of the tube as shown in the next pic.
Cutting8.jpg
