STEP/IGES Import

From Bend-Tech 7x Wiki
Revision as of 08:33, 17 September 2014 by Fabcam1 (talk | contribs)
Jump to: navigation, search

Bend-Tech 7x Wiki :: Main Menu Bar :: File :: Import :: STEP/IGES Import

Importing a File

Import 01.png
To import a file of one of these types, place the cursor on the "Import" option in the "File" menu and select an option from the menu. Choose a file to import in the Import (File Type) File window. Click "Open" to open it into an Import Part window.
Import 04.png












The main steps to follow when defining and importing a part are:

1.) Choose a material in the "Die and Material" tab.

2.) Define the desired part sections using the tools in the "Define" tab.

3.) Set the starting section of the part.

4.) As an option, choose a die for each bend on the part.

5.) Transfer the part to a single part designer, assembly, etc. using the "Transfer" menu. Transfer.png


  • Once each bent and straight section of the part is defined (the red tubes) using the definition tools, the starting straight length of the part will need to be defined.
  • Once the start length is chosen, the part will be tracked according to the chosen sections. All sections that are connected to the starting length/together will be included in the final imported part. The final part will be colored green. See below for an example.

Import 21.png


Die and Material

  • In the Die and Material tab, a material and die can be selected. The material selection will be shown in the 3D display of the imported part when the 'Preview Part' button is clicked.

Select Material

  • To select a material, click the drop down menu below "Select Material" and choose a material from the list. Once a material is selected, the diameter, wall thickness, and weight of the selected material will be shown to the right. Directly below the Select Material drop down menu, the original diameter of the imported part will be shown after 'Imported Diameter'. To view the material library, select the "Library" button next to the material selection. A material must be selected before a 3D shaded model of the part can be shown in the part display frame.

Select Die(s)

  • Once the part has be properly defined, each bend can have a die assigned to it. Click the drop down menu below the Die column and choose a die from the list. Above the bend chart, the original CLR of the imported part will be shown after 'Imported CLR:'. To view the die library, click the Library button next to the die selection.

Import 03.png



Define

Import 05.png

Before a part can be fully imported, each section that needs to be included on the part must be defined.


Before beginning, keep in mind that a section is represented by a lighter red shade as seen below. This does not represent the part that will be imported. This only defines which sections can be included in the part definition. When single parts are first brought into the import interface, the part sections may already be defined.

Import 06.png


Also, sections are defined based off the centerline. So, for example, if the Two points tool is used to define a section, the line between those two points will be used to represent the centerline of that section.




Define Straight Section

  • Two Points: To define a section using two points, click the Two Points button. Two points.png First, click on one pick point. Once the first point is clicked, a green wireframe preview of the section will generate from this point. To place the end of this section, click on another pickpoint.

Import 07.png


  • Circle -> Distance: To define a section by selecting a circle and any point, click the Circle -> Distance button. Circle distance.png First, click on a circle feature. Once the circle is selected, a green wireframe preview of the section will generate from this point. Next, define the length of the section by choosing a pickpoint.

Import 08.png


  • Line: To define a section by selecting a line feature, click the Line button. Import line.png Next, click on a line feature that will represent the centerline of the section.

Import 09.png


Define Bend

  • Two Circles: To define a bend between two circle features, click the Two Circles button. Two circles.png Next, click on the first circle. Once the circle is selected, a green wireframe preview of the section will generate from this point. Then click on another circle to place the section.

Import 10.png


  • Center, Start, End: To define a bend by selecting the center, start, and end points, click the Center, Start, End button. Center start end.png Next, click the centerpoint of the bend. This point will be located off the bend, at the center of the arc as if it were a full circle. Then click on the starting point of the arc and lastly, the end point of the arc to place the section.

Import 11.png


  • Start, Mid, End: To define a bend by defining the starting point, mid point, and end point, click the Start, Mid, End button. Start mid end.png First, selecting the centerline start point of the arc, the mid point, and then the centerline end point.



  • Arc: To define a bend by selecting an arc feature, click the Arc button. Import arc.png Next, click on an arc feature that will represent the centerline of the bend.

Import 12.png


  • Two Straights: To define a bend by selecting the straight lengths on either side, click the Two Straights button. Two straights.png Click on the line on one side of the arc, then click on the line on the other side.

Import 13.png


  • Reverse Last: Click the Reverse Last button to reverse the last bend


Show/Hide Features

  • Hide Feature: To hide a single line, arc, or circle feature, first click the Hide Feature button. Hide feature.png Then, click directly on the feature.

Import 14.png


  • Show All Features: To show all hidden line, arc, and circle features again, click the Show All Features button. Show all features.png


  • Auto Hide: To hide all inside line, arc, and circle features, click the Auto Hide button. Auto hide.png

Import 20.png


Modify Sections

  • Extend Straight: To add or remove length from a straight section of tube, click the Extend Straight button. Next, click on the section that will be adjusted. Then enter the amount to add or remove (enter as a negative to shorten) and click the OK button.

Import 15.png


  • Combine Straights: To fuse two straight sections together, click the Combine Straights button. Next, click on the first straight, then the second straight lengths that will be combined.

Import 16.png


  • Trim/Extend: To trim or extend a straight section in order for it to line up with a bent section, click the Trim/Extend button. First, click the straight section that will be adjusted. Next, click on the bent section that the section will line up to.

Import 17.png


  • Remove Section: To remove a defined section from the part, click the Remove Section button. Remove section.png Then just click on a light red section for it to be removed.

Import 18.png


  • Remove All: To remove all defined sections, click the Remove All button. Remove all.png


  • Set Start: To set the starting section of the part, click the Set Start button. Set start.png This section will define where the part begins and must be a straight length, bends cannot be used as the starting length. After clicking the button, simply click on a section of tube to set it as the start. Once selected, the start section will turn yellow. Note: Once the start is chosen, the part will be tracked. The tracked sections that will be included in the imported part will be shaded green.

Import 19.png




Verify

Under the Verify tab, the selected feature's attributes will be shown. Click on a feature to select it. If the selected feature is a line, the length, start and end points will be shown. If the selected feature is an arc, the radius, angle, center, start, and end locations will be shown.


Import 02.png



Settings

Import References

Die References

Import dxf 4.png

Die references can be set up by clicking the Die button [[File:]] below 'Import References'. This will open the Die References window. The purpose of die references is to automatically assign a die to any bends in a part that have the same material and import radius as the reference. For example, if an imported part is brought into the import interface and is assigned a material that matches the material reference (Under Die and Material in the top right corner) and has the same import radius as the die reference, once 'Generate Part' is clicked, the die reference die will be automatically chosen as the die in the Part Details chart. On the left side of the die references window, there is a list of die references. To view information about a die reference, select it by clicking its name in the list. The fields to the right will display the selected die reference's details. To add a new die reference, click the 'New' button at the bottom of the window. Enter the die reference's name in the 'Name:' field, select a die from the Die drop down menu, select a material from the 'Material' drop down menu, enter an import radius, and select which units to use. Click the 'Apply' button to add it to the list. To delete a die reference, select the die reference from the list and click the 'Delete' button. Click 'Close' to close the Die References window.





Material References

Import dxf 5.png

Material references can be set up by clicking the Material button Material ref.png below 'Import References'. This will open the Material References window. The purpose of a material reference is to automatically select a material for a part if it has the same import diameter of the material reference. For example, if an imported part has a 2 inch diameter and a material reference's assigned import diameter is 2 inches, the material reference material will be automatically selected (Under Die and Material in the top right corner) once the part is brought into the import interface. A list of all material references will be shown on the left side of the window. To view information about a material reference, select it by clicking its name in the list. The fields to the right will display the selected material reference's details. To add a new material reference, click the 'New' button at the bottom of the window. Enter the material reference's name in the 'Name:' field, select a material from the Material drop down menu, enter a import diameter in the 'Import Diameter' field, and select which units to use. Click the 'Apply' button to add it to the list. To delete a material reference, select the material reference from the list and click the 'Delete' button. Click 'Close' to close the Material References window.


Display Options

  • Display TriStar: The axis will be shown on the graphical display.
  • Display Features: The outline lines for the arcs and straight lengths will be displayed on the part model.
  • Display Sections: The defined, lighter red sections of tube will be shown on part model.
  • Display Part: Once the part is defined, the part will be shown in the selected material.
  • PickPoint Size: Use the PickPoint size drop down menu to change the size of all PickPoints in the Import part display.
Retrieved from "http://www.bend-tech.net/wiki7/index.php?title=STEP/IGES_Import&oldid=3287"