Difference between revisions of "Single Part -Interface/General Functions"

Latest revision as of 07:48, 21 October 2015

Bend-Tech 7x Wiki :: Single Part Interface/General Functions

Whenever a single part (Template, Custom Part, Custom 3D Part, XYZ Part, Sketch 3D, Sketch 2D, Reverse Design, or Straight Part) is being created, the interface will generally be the same for each with the exception of the part information/creation section below the tabbed menu.

The screen is broken up into four sections with a small icon menu near the top of the frame. The top left corner holds the tabbed section, the top right corner holds the results table, the bottom right holds the 3D display area, and the bottom left is the part information/creation section; usually containing value fields to create the user's desired design more easily.

Tabs

In the top left corner, there is a tabbed section that holds a majority of the design options.

Die & Material

Under the Die & Material tab, the material and die can be chosen.

To select a die, choose one from the drop down menu below 'Select Material:'. To see more detailed information about each material, click the 'Library' button next to the material menu to view the material library. To the right of the material selection, the diameter, wall thickness, and weight of the selected material will be displayed.

To select a die, choose one from the drop down menu below 'Select Die:' or click the 'Detailed List' button. Once the 'Detailed List' button has been clicked, a new window containing a chart of every die in the die library along with detailed information about each. To select a die from this list, click on a die and click the 'Select' button or double click on the desired die. To print this list, click the 'Print' button. Click the 'Library' button next to the die menu to view the die library.

To create a custom die CLR, click the 'Custom CLR' button. Enter the CLR value and click 'OK'. This will add the entered CLR value to the die drop down menus (next to each bend) as 'Custom CLR - (Entered Value). Select the custom CLR from the menu to use it.To the right of the die selection, the CLR, calibrated CLR, and bend location offset of the selected die will be displayed.

Part Details

Under the Part Details tab, notes, revision information, part description, cut-off start/end values, and the bend order menu can be accessed.

To add notes, type in the "Notes" field below. Any notes shown here will be included on the setup sheet. To set a default note, Select "Options" under the Tools menu and go to the Single Parts tab. If desired, enter any revision information next to "Revision" and a description next to "Description".

Type in any cut-off values into the "Cut-Off Start" and/or "Cut-Off End" fields. These cut-off values are the amount of extra material needed on either end of the part when bending.

Check the "Reverse Designed" check box to specify whether that part is designed from the opposite end of the current design.

Select the "Bend Order" button to access the Part Bending Order menu. In this window users can view their part being bent in a simulation. This window also contains settings and bending options. See the Bend Order page for further information on this feature.

Select the "Reset Bend Order" button to reset the bend order back to normal.

Select the "Part Settings" button to adjust the general settings, results/output settings, and reverse design settings for the current part. See the Part Settings page for further information on this feature.

Display

Under the "Display" tab, settings specific to the 3D part display can be adjusted. Select the button below "Cut-Off Color" to change the color that cut-off lengths will be displayed in. This button will display the current color that is in use. To change the size of the Tri-Star or Dimension text, enter values into either of the Tri-Star Scale or Dimension Size field.

Check the box next to Dimensions to have the length measurements and markers displayed in the part display.

Check the box next to Cut-Off to have any cut-off lengths that were entered in the 'Cut-Off Start or End' fields in the Part Details tab shown in the part display.

Check the box next to Apex Guides to to show lines extending from the bend verification points to the part.

Check the box next to Tri-Star to have the XYZ compass/tri-star displayed in the part display.

Check the box next to Wall Thickness to have the thickness of the material shown on the part model when in shaded mode.

Check the box next to the Verification Points to display blue points on the apex of each bend and the start and end of the part.

Check the box next to Bend Highlight to have whichever bend is currently selected (either the cursor is in the design field or selected in the bend list) highlighted on the part model.

Check the box next to Refresh on Keystroke to have the part model constantly updated whenever changed are made to the design.

While any of these options are unchecked, they will not be shown in the current 3D part display area.

Tasks

"Those below with simple functions that are self-explanatory will not have a link to further explanation for how to use the function."

Verify

Select the "Verify" button to open the Part Verify window. Using this tool, the dimensions/distances and the angle between two points can be verified.

Flat Layout

Select the "Flat Layout" button to open the Flat Layout window. Two flat, unbent models of the same part will be displayed and can be labeled and then printed out.

Bump Bending

Select the "Bump Bending" button to add bump bends to a bend on the current part. Bump bending allows bends to be sectioned off into multiple smaller, equal sized bends.

Price

Select the "Price" button to access the Price List window. There, the total costs for a single part, along with a specified amount of the current part can be seen.

Display XYZ/LRA (Excludes XYZ Part Design)

Depending on which coordinate mode is in use in the Results Table, this button will display either 'Display XYZ' or 'Display LRA'. When one mode is in use, the opposite will be shown on this button. Select this "Display XYZ/LRA" button to toggle between them. The results tables for the same part are shown below; LRA table on the left and XYZ table on the right.

Move to Origin (Specific to XYZ Part)

Select the "Move to Origin" button will make it so the starting point of the part will be located at (0, 0, 0). All other points on the point will be adjusted accordingly, so the design will remain the same once the origin is shifted.

Trim Cuts

If the current part has any cuts applied to the ends (which can be done in the Assembly interface in the Cutting tab), the excess material on the end(s) of the part can be removed by selecting the "Trim Cuts" button. The shape of the cut will then be visible. Note: For the cuts to be shown, the Cut-off display option needs to be turned off. This can be done in the Display Tab.

Inch vs MM

Select the "Inch vs MM" button to convert the current units to inches or millimeters. These changes will be shown in the results table, part information/design section, and 3D part display.

Apex vs. Tangent

Select the "Apex vs Tangent" button to switch the dimension types between apex and tangent for all of the current part's bends.

Print Scale

Select the "Print Scale" button to open the print scale feature. Print Scale allows a full size, to scale, 2D version of single part designs to be printed to scale on multiple sheets.

Adjust Centerline

Select the "Adjust Centerline" button to change how the part measurements are interpreted. In the part designers, parts are assumed to be based on centerline. This tool allows the current part dimensions to be from the inside or outside of the tube instead.

Manuf. Warning

Under the "Manuf. Warning" tab, manufacturing warnings will be listed if any are available. If there are warnings, a red block will be displayed above the tab. The bend number, description of the problem, and any action that can be taken will be listed for each warning. If an auto-fix is available, double-click on the auto-fix description to execute the auto-fix.

Part Settings Icon

In the upper right corner of the tabbed section, there will be a icon that can be used to access the part settings. For information on the part settings in this menu, see the "Part Settings" page.

Part Display

On the lower right side of the window is the 3D preview of the part. While creating a Custom, Custom 3D, XYZ, or Reverse Design part, the current bend and/or length will be highlighted in red while the bend is either selected or while the bend/start/end coordinate row is selected.
This preview can be adjusted by zooming, panning, and rotating.
To zoom, use the scroll wheel on the mouse. Scroll up to zoom out and scroll down to zoom in.
To pan/move the part preview, click and hold the scroll wheel or both mouse buttons and move the cursor around. The part preview will move with the cursor.
To rotate, click and hold the right mouse button. Move the cursor around and the part will rotate with the cursor movements.

Results Table

In the upper right corner of the window, the results table is shown.
The top section of the results table shows the die, material, cut length, and weight of the part.
This entire section's color will indicate if any problems exist. If the section is green, it means the part is complete and there are no problems or manufacturing warnings. If section is orange, the part is complete, but some problems or warnings exist. If the section is red, the part is not complete and/or there are warnings or problems with the part design.
The results table also holds a chart that lists each bend along with the bend order, location of the bend, amount of rotation needed for the bend, angle of the bend, spring angle value, centerline rotation, bend length, and the orientation of the bend. Double click within this chart to view a full size version in a new window. In this new window, select the "Print" button to print the chart.

Difference between revisions of "Single Part -Interface/General Functions"

Latest revision as of 07:48, 21 October 2015

Contents

Tabs

Die & Material

Part Details

Display

Tasks

Manuf. Warning

Part Settings Icon

Part Display

Results Table

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

Tools

@@ Line 1: / Line 1: @@
-'''[[Main Page|Bend-Tech 7x Wiki]] :: Single Part - Interface/General Functions'''
+'''[[Main Page|Bend-Tech 7x Wiki]] :: Single Part Interface/General Functions'''
-__NOTOC__
 [[File:single_part_1.png|right|450px]]
-Whenever a single part (Template, Custom Part, Custom 3D Part, XYZ Part, Sketch 3D, Sketch 2D, Reverse Design, or Straight Part) is being created, the interface will generally be the same for each with the exception of the part information/creation section below the tabbed menu.
+*Whenever a single part (Template, Custom Part, Custom 3D Part, XYZ Part, Sketch 3D, Sketch 2D, Reverse Design, or Straight Part) is being created, the interface will generally be the same for each with the exception of the part information/creation section below the tabbed menu.
-The screen is broken up into four sections with a small icon menu near the top of the frame. The top right corner holds the tabbed section, the top left corner holds the results table, the bottom left is the 3D part display, and the bottom right is the part information/creation section.
+*The screen is broken up into four sections with a small icon menu near the top of the frame. The top left corner holds the tabbed section, the top right corner holds the results table, the bottom right holds the 3D display area, and the bottom left is the part information/creation section; usually containing value fields to create the user's desired design more easily.
@@ Line 18: / Line 18: @@
+==Tabs==
+In the top left corner, there is a tabbed section that holds a majority of the design options.
+==Die & Material==
+Under the Die & Material tab, the material and die can be chosen.
+[[File:single_part_4.png|right]]
+'''To select a die''', choose one from the drop down menu below 'Select Material:'. To see more detailed information about each material, click the 'Library' button next to the material menu to view the material library. To the right of the material selection, the diameter, wall thickness, and weight of the selected material will be displayed.
+'''To select a die''', choose one from the drop down menu below 'Select Die:' or click the 'Detailed List' button. Once the 'Detailed List' button has been clicked, a new window containing a chart of every die in the die library along with detailed information about each. To select a die from this list, click on a die and click the 'Select' button or double click on the desired die. To print this list, click the 'Print' button. Click the 'Library' button next to the die menu to view the die library.
+'''To create a custom die CLR''', click the 'Custom CLR' button. Enter the CLR value and click 'OK'. This will add the entered CLR value to the die drop down menus (next to each bend) as 'Custom CLR - (Entered Value). Select the custom CLR from the menu to use it.To the right of the die selection, the CLR, calibrated CLR, and bend location offset of the selected die will be displayed.
-<h2>Icon Toolbar</h2>
-[[File:single_part_2.png]]
+==Part Details==
+[[File:single_bend_part1.png|right]]
+*Under the Part Details tab, notes, revision information, part description, cut-off start/end values, and the bend order menu can be accessed.
-At the top of the frame just below the main menu bar, there is a series of icons.
+*To add '''notes''', type in the "'''Notes'''" field below. Any notes shown here will be included on the setup sheet. To set a default note, Select "'''Options'''" under the '''Tools''' menu and go to the '''Single Parts''' tab. If desired, enter any revision information next to "'''Revision'''" and a description next to "'''Description'''".
-Click the '''New Part''' icon [[File:newpart.png]] to open the create new menu. This menu will allow you to choose a new part designer interface and begin a new part design.
+*Type in any '''cut-off''' values into the "'''Cut-Off Start'''" and/or "'''Cut-Off End'''" fields. These cut-off values are the amount of extra material needed on either end of the part when bending.
-Click the '''New Assembly''' icon [[File:newassembly.png]] to open a new assembly design. See the [[Assembly]] page for further information on creating an assembly.
+*Check the  "'''Reverse Designed'''" check box to specify whether that part is designed from the opposite end of the current design.
-Click the '''New Plate''' icon [[File:newplate.png]] to open a new plate design. See the [[Plate]] page for further information on designing a plate.
+*Select the "'''Bend Order'''" button [[File:bendorder_1.png]] to access the '''Part Bending Order''' menu. In this window users can view their part being bent in a simulation. This window also contains settings and bending options. See the '''[[Bend Order]]''' page for further information on this feature.
-Click the '''New Header''' icon [[File:newheader.png]] to open a new header design. See the [[Headers (Create & Edit)|Header]] page for further information.
+*Select the "'''Reset Bend Order'''" [[File:bendorder_10.png]] button to reset the bend order back to normal.
-Click the '''Open''' icon [[File:open.png]] to open a part, assembly, plate, or header file.
+*Select the "'''Part Settings'''" [[File:part_settings.png]] button to adjust the general settings, results/output settings, and  reverse design settings for the current part. See the '''[[Part Settings]]''' page for further information on this feature.
-Click the '''Save''' icon [[File:save_icon.png]] to save the current active window's progress. If the current window is a new and hasn't been saved previously, the part will need to be given a name and location. Click 'Save' in the Save window to save.
+==Display==
+[[File:single_part_6.png|right]]
+Under the "'''Display'''" tab, settings specific to the 3D part display can be adjusted. Select the button below "'''Cut-Off Color'''" to change the color that cut-off lengths will be displayed in. This button will display the current color that is in use. To change the size of the Tri-Star or Dimension text, enter values into either of the '''Tri-Star Scale''' or '''Dimension Size''' field.
-Click the '''Print''' icon [[File:printer.png]] to print the part's setup sheet. To add or remove anything from this page, check/uncheck any of the printing options in the Settings tab in the tabbed section near the upper left corner of the part design frame.
+Check the box next to '''Dimensions''' to have the length measurements and markers displayed in the part display.
-Click the '''Print Preview''' icon [[File:preview.png]] to view a preview of the setup sheet. Use the icons in the top left corner to adjust the zoom and the amount of pages shown. Click the 'Print' button to print the setup sheet. Click 'Close' to close the print preview without printing.
+Check the box next to '''Cut-Off''' to have any cut-off lengths that were entered in the 'Cut-Off Start or End' fields in the Part Details tab shown in the part display.
-Click the '''Solidworks''' icon [[File:solidworks.png]] to import a part file from Solidworks that has been sent to Bend-Tech.
+Check the box next to '''Apex Guides''' to to show lines extending from the bend verification points to the part.
-Click the '''Display''' menu [[File:display.png]] to alternate between a line or shaded part model.
+Check the box next to '''Tri-Star''' to have the XYZ compass/tri-star displayed in the part display.
-Click the '''Refresh''' icon [[File:refresh.png]] to refresh the part display.
+Check the box next to '''Wall Thickness''' to have the thickness of the material shown on the part model when in shaded mode.
-Click the '''Home''' button [[File:home.png]] to reset the 3D part display to its original default view.
+Check the box next to the '''Verification Points''' to display blue points on the apex of each bend and the start and end of the part.
-Click the '''Zoom''' button [[File:zoom.png]] to zoom all the way in on the current view of the 3D part display and fit it to the display frame.
+Check the box next to '''Bend Highlight''' to have whichever bend is currently selected (either the cursor is in the design field or selected in the bend list) highlighted on the part model.
-Click on the '''Transfer''' menu [[File:transfer.png]] to send the current part design to any of the other part designers, a new or current assembly design, a new or existing nesting project, the offset part interface, or the break part interface.
+Check the box next to '''Refresh on Keystroke''' to have the part model constantly updated whenever changed are made to the design.
-Click on the '''Projections''' icon [[File:project.png]] to view the current part model from a specified plane (top, bottom, left, right, front, or back) or from a certain angle.
+While any of these options are unchecked, they will not be shown in the current 3D part display area.
-<h2>Tabs</h2>
-In the top right corner, there is a tabbed section that holds a majority of the design options.
+==Tasks==
+[[File:single_part_3.png|right]]
-<h3>Die & Material</h3>
-Under the Die & Material tab, the material and die can be chosen.
-[[File:single_part_4.png|right]]
-'''To select a die''', choose one from the drop down menu below 'Select Material:'. To see more detailed information about each material, click the 'Library' button next to the material menu to view the material library. To the right of the material selection, the diameter, wall thickness, and weight of the selected material will be displayed.
-'''To select a die''', choose one from the drop down menu below 'Select Die:' or click the 'Detailed List' button. Once the 'Detailed List' button has been clicked, a new window containing a chart of every die in the die library along with detailed information about each. To select a die from this list, click on a die and click the 'Select' button or double click on the desired die. To print this list, click the 'Print' button. Click the 'Library' button next to the die menu to view the die library.
-'''To create a custom die CLR''', click the 'Custom CLR' button. Enter the CLR value and click 'OK'. This will add the entered CLR value to the drop down menu as 'Custom CLR - (Entered Value). Select the custom CLR from the menu to use it.To the right of the die selection, the CLR, calibrated CLR, and bend location offset of the selected die will be displayed. Check the box next to 'Display Spring Angle' to have spring angle values included in the results table.
-<h3>Part Details</h3>
-[[File:single_part_5.png|right]]
-Under the Part Details tab, notes, revision information, part description, cut-off start/end values, and the bend order menu can be accessed.
-'''To add notes''', type in the field below 'Notes:'. Any notes shown here will be included on the setup sheet. To set a default note, Select 'Options' under the 'Tools' menu and go to the Single Parts tab. If desired, enter any revision information next to 'Revision:' and a description next to 'Description:'.
-Enter any '''cut-off''' values into the 'Cut-Off Start' and/or 'Cut-Off End' fields. These cut-off values are the amount of extra material needed on either end of the part when bending.
+*"'''Those below with simple functions that are self-explanatory will not have a link to further explanation for how to use the function.'''"
+'''[[Verify]]'''
+*Select the "'''Verify'''" [[File:verify.png]] button to open the '''Part Verify''' window. Using this tool, the dimensions/distances and the angle between two points can be verified.
-'''[[Bend Order]]:''' Click the '''Bend Order''' button [[File:bendorder_1.png]] to access the 'Part Bending Order' menu. In this window, a simulation of the part being bent is shown along with settings and bending options. See the [[Bend Order]] page for further information on this feature.
+'''[[Flat Layout]]'''
+*Select the "'''Flat Layout'''" [[File:flatlayout.png]] button to open the '''Flat Layout''' window. Two flat, unbent models of the same part will be displayed and can be labeled and then printed out.
-<h3>Display</h3>
-[[File:single_part_6.png|right]]
-Under the Display tab, settings specific to the 3D part display can be adjusted in this tab. Click the button below 'Cut-Off Color' to change the color that cut-off lengths will be displayed in. This button will display the current color that is in use. To change the size of the Tri-Star or Dimension text, enter values into either of the 'Tri-Star Scale' or 'Dimension Size' field.
-Check the box next to 'Display Dimensions' to have the length measurements and markers displayed in the part display (Specific to Template).
+'''[[Bump Bending]]'''
+*Select the "'''Bump Bending'''" [[File:bumpbending.png]] button to add bump bends to a bend on the current part. Bump bending allows bends to be sectioned off into multiple smaller, equal sized bends.
-Check the box next to the 'Verification Points' to display blue points on each bend and the start and end of the part (Specific to Template).
-Check the box next to 'Display Cut-Off' to have any cut-off lengths that were entered in the 'Cut-Off Start or End' fields in the Part Display tab shown in the part display.
-]Check the box next to 'Display Apex Guides' to to show lines extending from the bend verification points to the part.
+'''[[Price]]'''
+*Select the "'''Price'''" [[File:price.png]] button to access the '''Price List''' window. There, the total costs for a single part, along with a specified amount of the current part can be seen.
-Check the box next to 'Display Tri-Star' to have the XYZ compass/tri-star displayed in the part display. Check the box next to 'Display Material Thickness' to have the hollow center of the tube (determined by the chosen material's wall thickness) displayed instead of just a solid part.
-While any of these options are unchecked, they will not be shown in the 3D part display.
+'''Display XYZ/LRA''' (Excludes XYZ Part Design)
+*Depending on which coordinate mode is in use in the Results Table, this button will display either 'Display XYZ' or 'Display LRA'. When one mode is in use, the opposite will be shown on this button. Select this "'''Display XYZ/LRA'''" [[File:displayxyz.png]] button to toggle between them. The results tables for the same part are shown below; LRA table on the left and XYZ table on the right.
+::[[File:single_part_17.png|600px]]
-<h3>Tasks</h3>
+'''Move to Origin''' (Specific to XYZ Part)
-[[File:single_part_3.png|right]]
+*Select the "'''Move to Origin'''" [[File:movetorigin1.png]] button will make it so the starting point of the part will be located at (0, 0, 0). All other points on the point will be adjusted accordingly, so the design will remain the same once the origin is shifted.
-*'''[[Verify]]:'''
-Click the 'Verify' button to open the Part Verify tool. Using this tool, the dimensions/distances and the angle between two points can be verified.
-To change the view of the part, select Top, Left, Front, Bottom, Right, or Back.
+'''Trim Cuts'''
+*If the current part has any cuts applied to the ends (which can be done in the [[Assembly]] interface in the '''Cutting''' tab), the excess material on the end(s) of the part can be removed by selecting the "'''Trim Cuts'''" [[File:trimcuts.png]] button. The shape of the cut will then be visible.  '''''Note:''''' For the cuts to be shown, the '''Cut-off''' display option needs to be turned off. This can be done in the [[#Display|Display Tab]].
-To zoom in/out, use the mouse scroll wheel.
-To move/pan, click and hold the scroll wheel or both mouse buttons and move the cursor around.
+'''Inch vs MM'''
+*Select the "'''Inch vs MM'''" [[File:inchvsmm.png]] button to convert the current units to inches or millimeters. These changes will be shown in the results table, part information/design section, and 3D part display.
-Place points by clicking on or around the part display. One two points have been selected, the horizontal, vertical, and linear distances along with the angle will be shown. A visual representation of the angle will be shown directly below the angle value. The size of the points can be changed by selecting a size from the drop down menu next to 'Point Size:'. To have all point selections restricted to a grid, check the box next to 'Snap to Grid'.
+'''[[Apex vs. Tangent]]'''
+*Select the "'''Apex vs Tangent'''" [[File:apexvstangent1.png]] button to switch the dimension types between apex and tangent for all of the current part's bends.
-*'''Flat Layout:'''
+'''[[Print Scale]]'''
-Click the 'Flat Layout' to open the Flat Layout window. Two flat, unbent models of the same part will be displayed.
+*Select the "'''Print Scale'''" [[File:printscale.png]] button to open the print scale feature. Print Scale allows a full size, to scale, 2D version of single part designs to be printed to scale on multiple sheets.
-On the left side of the window is occupied by the Display Dimensions section. Under Left/Right Model, the left and right models each have the option to display the start, center, or end of the bends. Check the box next to the desired option(s) to have them displayed on the part display. Under Bends, check Rotations, Angles, and/or CLR to have them displayed on the part display. Rotations and angles will only be shown on the right model while CLR is only shown on the left. Under 'Fraction/Decimal Display:', the decimal or fraction tolerance for the part display measurements can be chosen by clicking an option from the drop down menu. Changing the point size can by done by choosing a size from the drop down menu below 'Point Size:'.
-Below the Display Dimensions section is the Dimensions section. Click the 'Move' button to change the location of any of the displayed dimensions. Once the button has been clicked, each dimension will have a blue dot next to it. Click on the dot and move the cursor to a new location and click again to place the dimension. Click the 'Suppress' button to remove a dimension from the display. Once clicked, each dimension will have a blue dot next to it. Click on the dimension to remove it. Click the 'Display All' button to have all dimensions that were previously suppressed displayed again.
+'''[[Adjust Centerline]]'''
+*Select the "'''Adjust Centerline'''" [[File:adjustcenterline.png]] button to change how the part measurements are interpreted. In the part designers, parts are assumed to be based on centerline. This tool allows the current part dimensions to be from the inside or outside of the tube instead.
-On the right side of the part display, a small 3D part preview is displayed along with some basic information of the part and any notes that were added to the part. Click the 'Print' button to print the current view of the flat layout, 3D model, part information, and notes. Click the 'Close' button to close the Flay Layout window.
-Below the part display, there is a 'Display Settings' button. Click to access the settings for the flat layout display. Under Flat Layout - Sizes, the text size along with the stand-off (distance between dimension lines and the part surface) values for dimensions, angle, rotation, and CLR can be adjusted. Under Flat Layout - Abbreviations, the abbreviations for angle, rotation, and centerline radius can be changed. To change, enter a new abbreviation into the field next to any of the options. These abbreviations will only be applied to the flat layout display. Under Flat Layout - Colors, the colors of the tube, bends, extensions, and text can be changed. To change color of any of these features, click the button and choose a new color in the Color menu. The buttons will display the currently selected color of the feature. Click the 'Set Defaults' button to set the current selected sizes, colors, and abbreviation as the defaults in the Global Settings (These can be accessed through the Tools menu in Options). Click the 'Restore Defaults' button to reset the settings back to the original default settings.
-*'''Bump Bending:'''
+==Manuf. Warning==
+[[File:single_part_8.png|right]]
+*Under the "'''Manuf. Warning'''" tab, manufacturing warnings will be listed if any are available. If there are warnings, a red block will be displayed above the tab. The bend number, description of the problem, and any action that can be taken will be listed for each warning. If an auto-fix is available, double-click on the auto-fix description to execute the auto-fix.
-*'''Timing:'''
+==Part Settings Icon==
+[[File:single_part_18.png|right|350px]]
+*In the upper right corner of the tabbed section, there will be a [[File:part_settings_icon.png]] icon that can be used to access the part settings. For information on the part settings in this menu, see the "'''[[Part Settings]]'''" page.
-*'''Price:'''
-Click the 'Price' button to access the Price List. In this menu the total costs for a single part, along with a specified amount of the current part can be seen. A chart containing the part's material, length, bend number, die, labor, and cost and time for each. These cost settings can be set up in the Tools Menu under Pricing Settings. To add another column that will calculate the price for a specified amount of the part, enter a value into the Quantity First Field area or adjust the amount using the up and down arrows. Up to two extra columns can be added. To add a second column, enter a value into the Quantity Second Field or adjust the amount using the up and down arrows. To adjust the size of the columns, place the cursor over the vertical dividing line at the very top of the chart in the title area. A double ended arrow will appear, just click and drag back and forth to increase or decrease the column size. To print the current view of the Price List chart, click the 'Print' button. Click 'Close' to close the Price List window.
-*'''Display XYZ/LRA:''' (Excludes XYZ Part Design)
-Depending on which coordinate mode is in use in the Results Table, this button will display either 'Display XYZ' or 'Display LRA'. When one mode is in use, the opposite will be shown on this button. Click this button to toggle between them. The results tables for the same part are shown below; LRA table on the left and XYZ table on the right.
-*'''Move to Origin:''' (Specific to XYZ Part)
-Click the 'Move to Origin' button will make it so the starting point of the part will be located at (0, 0, 0). All other points on the point will be adjusted accordingly, so the design will remain the same once the origin is shifted.
-*'''Trim Cuts:'''
-*'''Inch vs MM:'''
-Clicking the 'Inch vs MM' button will convert the current units to the other. These changes will be shown in the results table, part information/design section, and 3D part display.
-*'''Apex vs Tangent:'''
-*'''Print Scale:'''
-*'''Adjust Centerline:'''
+==Part Display==
-<h3>Manuf. Warning</h3>
-[[File:single_part_8.png|right]]
-Under the 'Manuf. Warning' tab, manufacturing warnings will be listed if any are available. While there are warnings, a red block will be displayed above the tab. The bend number, description of the problem, and any action that can be taken will be listed for each warning. If an auto-fix is available, double-click on the auto-fix description to execute the auto-fix.
-<h2>Part Display</h2>
 [[File:single_part_11.png|right|400px]]
-On the lower right side of the window is the 3D preview of the part. While creating a Custom, Custom 3D, XYZ, or Reverse Design part, the current bend and/or length will be highlighted in red while the bend is either selected or while the bend/start/end coordinate row is clicked in. This preview can be adjusted by zooming, panning, and rotating. To zoom, use the scroll wheel on the mouse. Scroll up to zoom out and scroll down to zoom in. To pan/move the part preview, click and hold the scroll wheel or both mouse buttons and move the cursor around. The part preview will move with the cursor. To rotate, click and hold the right mouse button. Move the cursor around and the part will rotate with the cursor movements.
+*On the lower right side of the window is the 3D preview of the part. While creating a Custom, Custom 3D, XYZ, or Reverse Design part, the current bend and/or length will be highlighted in red while the bend is either selected or while the bend/start/end coordinate row is selected.
+*This preview can be adjusted by zooming, panning, and rotating.
+*To zoom, use the scroll wheel on the mouse. Scroll up to zoom out and scroll down to zoom in.
+*To pan/move the part preview, click and hold the scroll wheel or both mouse buttons and move the cursor around. The part preview will move with the cursor.
+*To rotate, click and hold the right mouse button. Move the cursor around and the part will rotate with the cursor movements.
@@ Line 189: / Line 169: @@
-<h2>Results Table</h2>
+==Results Table==
 [[File:single_part_9.png|right]]
-In the upper right corner of the window, the results table is shown. The top section of the results table shows the die, material, cut length, and weight of the part. This entire section's color will indicate if any problems exist. If the section is green, it means the part is complete and there are no problems or manufacturing warnings. If section is orange, the part is complete, but some problems or warnings exist. If the section is red, the part is not complete and/or there are warnings or problems with the part design. The results table also holds a chart that lists each bend along with the bend order, location of the bend, amount of rotation needed for the bend, angle of the bend, spring angle value, centerline rotation, bend length, and the orientation of the bend. Double click within this chart to view a full size version in a new window. In this new window, click the 'Print' button to print the chart.
+*In the upper right corner of the window, the results table is shown.
+*The top section of the results table shows the die, material, cut length, and weight of the part.
+*This entire section's color will indicate if any problems exist. If the section is green, it means the part is complete and there are no problems or manufacturing warnings. If section is orange, the part is complete, but some problems or warnings exist. If the section is red, the part is not complete and/or there are warnings or problems with the part design.
+*The results table also holds a chart that lists each bend along with the bend order, location of the bend, amount of rotation needed for the bend, angle of the bend, spring angle value, centerline rotation, bend length, and the orientation of the bend. Double click within this chart to view a full size version in a new window. In this new window, select the "'''Print'''" button to print the chart.
 [[File:single_part_10.png|500px]]